VEIRA Tube Leveler
What does VEIRA Tube Leveler do?
It is VEIRA’s flagship tube limiter, in the tradition of the classic twin-channel vari-mu limiters of the late 1950s. Two complete channels, each with its own INPUT, THRESHOLD and TIME CONSTANT, hold a bus, a master or a single track together with a ratio that rises gently with level, and the tubes and transformers give it weight. Two big needle meters show each channel’s gain reduction. Use it on the mix bus and the master, on drums, bass and vocals, or in parallel.
Should I choose Tube Leveler or Comp Blue?
Both are vari-mu tube compressors with the same six time constants and a ratio that rises with level. VEIRA Comp Blue is one of the four colour compressors: one set of controls for both sides, with LEFT/RIGHT or LAT/VERT, and a COLOUR knob. VEIRA Tube Leveler is the flagship: two complete channels you can run apart, linked or as mid and side, each with its own settings; a tube cell whose harmonics grow with the reduction (about four times Comp Blue’s at the same 8.5 dB); transformers under IRON that weigh down the bass; and two big needle meters. Choose Comp Blue for clean, simple glue, and Tube Leveler when you want the full twin-channel unit and its heavier tube sound.
What do LEFT/RIGHT, LINK and LAT/VERT do?
They decide how the two channels work. LEFT/RIGHT runs them apart: channel A on the left, B on the right, each with its own controls and side chain, for hard-panned doubles or two mono sources on one stereo track. LINK, the default, lets channel A’s controls drive both with one control voltage from the louder side, so the stereo image never moves; channel B’s controls are dimmed. LAT/VERT works on the lateral signal (the mid, what both speakers share) with channel A and the vertical (the side) with channel B, each with its own side chain, so loud wide parts are held without touching the vocal, kick and bass in the centre. On a mono track only channel A is used.
Where is the ratio control?
There isn’t one, as on the classic units: the tubes set the ratio, and it rises with level. With THRESHOLD at −20 dBFS it is about 1.2:1 at the threshold, 2.5:1 at 8 dB over and about 4:1 when driven hard. For a firmer hold, lower THRESHOLD or add INPUT (and bring the level back with OUTPUT); for a gentler one, raise THRESHOLD. Watch the needle meters as you set it.
Which TIME CONSTANT should I use?
1 (0.3 s release) for drums and anything that should recover between hits; 2 (0.8 s), the most used, for mix buses, vocals and bass; 3 and 4 (2 and 5 s) for a slow, steady hold over whole sections. 5 and 6 are programme-dependent: after a single peak they let go in 2 s and 0.3 s, but after several peaks or sustained heavy compression the release lengthens to about 10 s, and with 6 up to 25 s. On a master, 5 and 6 are especially natural. In LEFT/RIGHT and LAT/VERT each channel has its own.
What does IRON do?
IRON sets how much of the input and output transformers and the output stage you hear. The transformers saturate on heavy lows, adding 3rd harmonic and weight to the bass, the output stage adds a little 2nd and 3rd, and the top rolls off gently (−0.7 dB at 10 kHz at 100 %). The default 30 % adds 0.08 % THD to a 1 kHz tone at −12 dBFS; at 100 % a loud 50 Hz note gets several percent. At 0 % the plugin is transformerless and clean. The tubes’ own harmonics come from the gain reduction, not from IRON: the more you compress, the more you hear them.
Does it add latency?
Yes: 98 samples at every sample rate (2.0 ms at 48 kHz), from the oversampling filters of the tube and iron stages. It is constant whatever the settings, reported to your DAW, which compensates automatically, and the host’s bypass and the dry signal under MIX are delayed by the same amount. With IRON at 0 % and no gain reduction the output is the input, delayed, bit for bit, in every mode.
What presets does it come with?
67 factory presets in 14 folders: Default, Drums, Bass, Guitar, Keyboards, Strings, Brass, Woodwinds, Vocals, Mix Bus, Mastering, Parallel, Lat-Vert and Creative FX, from Leveler Glue and Programme Glue TC5 to Master TC6, Steady Centre, Parallel Drum Crush and Tube Drive. Each preset’s THRESHOLD was fitted for its designed reduction on its folder’s material, then OUTPUT so it comes out as loud as it went in: within 0.10 dB outside Default. On your music, set THRESHOLD by the needle meters, then OUTPUT by ear. You can save your own.