VEIRA Limiter White
What does VEIRA Limiter White do?
It is a true-peak mastering limiter, the clean one of the four VEIRA colour limiters, painted pearl white. Turn GAIN up and it keeps every peak under the CEILING, in true peak. A slow stage looks ahead and decides how far each kind of sound may go, a transient clipper rounds the first milliseconds of the hits, and a fast stage takes the rest to the ceiling, so bass is never clipped, held notes are never shaved and the mix doesn’t pump. The loudness panel reads integrated loudness against your TARGET.
Which of the four colour limiters should I choose?
All four hold a true-peak ceiling with no overs, share the same loudness panel, TARGET and MATCH, and are built to reach −6 LUFS on a dense mix. What differs is the stage in front of the ceiling. White is clean: it changes the least, so start there if you’re not sure. Red is punch: its clipper keeps the drums hitting, for EDM, hip-hop, rock and dance pop. Gold is warm: tape or tube harmonics for a mix that feels thin or hard. Blue is vintage: optical or FET levelling and transformer colour for a mix that should breathe and glue.
Will it reach −6 LUFS on my mix?
On typical dense material, yes: on a premaster peaking at −3 dBFS it reached −6.06 LUFS integrated with the true peak at −1.06 dBTP and no overs, without distortion you can hear. At −6 LUFS any limiter shapes the peaks, and the grey shadow on the waveform shows how much. White never clips held bass, so on very sub-heavy mixes it can stop just short: a kick, bass and pads mix stopped at −6.8 LUFS. If more GAIN only adds reduction and the loudness stops moving, back off; Red, Gold or Blue go further on that kind of mix.
What do LOOKAHEAD, LINK and OVERSAMPLING change?
LOOKAHEAD (0.5 to 10 ms) sets how early the gain starts to come down before a peak: longer is smoother, shorter keeps more of the attack. You can change it while playing, and it never changes the latency. LINK (0 to 100 %) sets how much the two channels are limited together: 100 % keeps the stereo image still, less lets each side be limited on its own. OVERSAMPLING runs the fast stage at 1X, 2X or 4X (the default); above 1X the products of fast gain changes are filtered out instead of folding back.
What does MATCH do, and should I bounce with it on?
MATCH plays the result at the input’s loudness (K-weighted, over 3 seconds), so you can switch the plugin in and out and hear what the limiting does to the sound, not just that it got louder. The meters and the loudness panel keep measuring the real output. An offline bounce always leaves MATCH out; for a real-time bounce, switch it off first.
Does it add latency?
Yes, a constant 782 samples at 48 kHz (16.3 ms; 740 at 44.1 kHz), the lookahead and the oversampling filters. It is the same at every setting and reported to your DAW, which plays the track that much earlier, and the host’s bypass is delayed by the same amount, so a bypassed track stays in time. Put it on the master bus, last.
My bounce reads over the ceiling. Why?
Something after the limiter is changing the level: another plugin, the master fader, a pan law, or dither or a format conversion in the bounce. Put the limiter last on the master bus and leave the master fader at 0 dB. On its own it aims a hair under the CEILING, so a −1.0 dBTP ceiling reads about −1.05 dBTP on a standard true-peak meter, with no overs. A meter that reads sample peak will read a little lower; one with a different true-peak filter may differ by a few hundredths of a dB.
What presets does it come with?
43 factory presets in 10 folders: Default, Mastering, Streaming, Pop, EDM, Hip-Hop, Rock, Acoustic, Mix Bus and Stems. Each one names a loudness TARGET and was measured through the real plugin on matching material: no preset produces an over. Your music will differ in level, so set GAIN by the loudness panel until TO TARGET reads about 0 LU, as each preset’s note says. You can save your own with SAVE.