VEIRA EQ

What is VEIRA EQ for, and when should I use it?

VEIRA EQ is a parametric equaliser for every job from a single kick drum to the master bus, with up to 24 bands in six filter types: bell, low shelf, high shelf, low cut, high cut and notch. Any bell or shelf can also become dynamic, so it cuts or boosts only when its part of the spectrum gets loud, which is the tool for problems that come and go, such as sibilance or one booming bass note.

What's a good way to get started with VEIRA EQ?

A new instance opens with six bands ready (a low cut at 30 Hz and a high cut at 18 kHz, both off, plus a low shelf, two bells and a high shelf, all flat), so it passes your audio unchanged until you move something. Load a factory preset close to your job, for example Vocals ▸ Vocal Clean Up or Mastering ▸ Master Gentle Polish, then turn SCALE down from 100 % until it's just enough. Click anywhere on the graph to add a new bell at that frequency and gain.

What does the SCALE knob do?

SCALE turns the whole curve up or down in proportion: at 100 % every band's gain is as set, at 50 % every boost and cut is half as big, at 0 % the curve is flat and at 200 % every move is doubled. Cut filters and notches are not affected, because they have no gain. It's a quick way to try a bit more or a bit less of a whole EQ or a preset.

Why can't I change the gain of a band by dragging its handle up and down?

Cut filters and notches have no gain, so their handles only move left and right; use the mouse wheel over the handle to change their slope or Q instead. If it happens on a bell or shelf, check that SCALE isn't at 0 %, which flattens every band.

How do dynamic bands work, and what do THRESHOLD and RANGE mean?

Select a bell or shelf and press COMP (dip when loud) or EXP (rise when loud). THRESHOLD (−60 to 0 dBFS) is compared with the level of that band's own frequency region, not the whole track, and RANGE (0 to 24 dB) is the most the band will ever move. A quick setup: start with RANGE at the most you'd ever want, play the loudest section, lower THRESHOLD until the CHANGE readout moves only on the problem moments, then reduce RANGE until it's just enough.

Why are some knobs in the lower half greyed out?

The knobs always belong to the selected band, so if the title reads NO BAND SELECTED, click a chip or a handle. GAIN is greyed out on a notch because its depth is fixed, and the DYNAMICS section is greyed out for cuts and notches, which can't be dynamic. If the dynamic knobs are only dimmed, the band is set to OFF.

Does VEIRA EQ add latency? Does it work on mono tracks?

It adds no latency at all (0 samples) in every setting, so it's safe while recording and on any number of tracks. It works on mono and stereo tracks; in stereo both channels get exactly the same curve, so the stereo image never shifts.

EXT KEY is on, but the band reacts to the track rather than my kick or vocal. Why?

Your DAW hasn't connected VEIRA EQ's sidechain input, and with no sidechain a band with EXT KEY on simply listens to the track itself; route the key signal to the sidechain input in your DAW. If the key is connected but CHANGE doesn't move, the key is too quiet for the threshold in that band's region, so lower THRESHOLD.

Why is my track louder or quieter after EQ, and why does a dynamic preset do nothing?

Boosts add level and cuts remove it, so adjust OUTPUT until the Δ INTEGRATED reading on the meter bridge is about 0.0 LU before comparing with bypass. Dynamic presets assume tracks peaking around −8 dBFS (buses −4, master −3); if your track is hotter or quieter, move each dynamic band's THRESHOLD by the same number of dB.

Can I type a value, or make the window bigger?

Yes. Right-click a knob (Control-click on a Mac), type the value and press Return; double-click a knob to return it to its default. To resize the window, drag its bottom-right corner: it scales from 75 % to 200 %, keeps its proportions, and the size is saved with your session.