VEIRA EQ Blue

What does VEIRA EQ Blue do?

It is a console channel equalizer, the vintage one of the four VEIRA colour EQs, painted 1970s steel blue, in the tradition of the British inductor desks of that decade. An 18 dB/oct HIGH-PASS, a LOW shelf with its round bump and tight dip, a MID bell that narrows as you push it and a very gradual HIGH shelf sit on stepped frequencies, and COLOUR drives the console’s inductors and transformers. The curve screen shows each section and the total over the live spectrum.

Which of the four colour EQs should I choose?

All four draw their curve over the live spectrum, keep their curves’ analog shape up to 20 kHz and show the same meter bridge; what differs is the kind of EQ. White is clean and surgical: eight bands of any shape, SOLO and minimum or linear phase, for precise fixes and transparent mastering. Red is mid/side: every band on the stereo signal, the mid, the side or one channel, with BASS MONO, AIR and WIDTH. Gold is warm: a passive tube program EQ with the low boost-and-attenuate trick, a silky top and TUBE drive. Blue is vintage: a 1970s British inductor console EQ with stepped frequencies and COLOUR. Each manual has a page comparing them.

Why does the low shelf make a small dip above its frequency?

That is the inductor shelf’s shape: half its gain at the dial, a small bump below it and a small dip of the opposite sign above it, so a boost sounds round and tight instead of boomy. At +16 dB the bump and dip are about 0.94 dB at 60 Hz, larger at 35 Hz and smaller at 220 Hz, and a cut mirrors them. The sizes are VEIRA’s model of the published behaviour, in the small range described for the hardware.

What does COLOUR do?

COLOUR drives the console’s transformers, inductors and class-A stage on what the EQ made: the lows saturate first, big boosts thicken and a small 2nd harmonic is added. At 100 %, a 50 Hz tone at −3 dBFS gets 47 dB more 3rd harmonic than a 1 kHz tone at the same level. 15 to 35 % adds weight and glue without audible distortion; at 0 % Blue is clean. It runs at four times the sample rate, so nothing aliases.

What does STEPS do?

STEPS makes the three gains, LOW, MID and HIGH, click in 2 dB steps, as on the stepped consoles, so settings can be written down and recalled exactly. Off, the default, they turn smoothly. The frequency knobs always click between the console’s positions, and the curve glides to a new position, so stepping never clicks.

Why does everything sound better with Blue in?

Probably because it is louder: Blue has no automatic gain, and boosts add level. Trim OUTPUT until the Δ on the meter bridge reads about 0.0 LU, then compare with bypass, or use EQ IN, which switches the EQ and high-pass out while COLOUR and OUTPUT stay. Every factory preset’s OUTPUT is already set to come out as loud as it went in.

Does it add latency?

A small one: 64 samples at 44.1 to 96 kHz (1.3 ms at 48 kHz) for the oversampling filters, none at 176.4 and 192 kHz. It is always the same and reported to your DAW, which compensates; the host’s bypass is delayed by the same amount. With the high-pass off, every gain at 0 and COLOUR at 0 %, the output is the input, delayed, bit for bit.

What presets does it come with?

43 factory presets in 9 folders: Default, Drums, Bass, Guitars, Keys, Vocals, Mix Bus, Mastering and Creative, from Kick Punch, Vocal Forward and Console Bus to Master Console and Lo-Fi Console. Each preset’s OUTPUT was fitted on its folder’s material so it comes out as loud as it went in, within 0.06 dB. COLOUR was set for tracks peaking at −8 dBFS and buses at −4: hotter tracks get more colour.

VEIRA EQ Blue · Help · VEIRA