VEIRA Harmonic Saturator
What is VEIRA Harmonic Saturator for?
It adds harmonics, the quieter copies of each note at two to five times its pitch, which we hear as warmth, thickness, edge or air. Use it to make a bass heard on a phone, bring a vocal forward, make a drum bus feel denser or give a mix an analog sound. The signal is split into LOW, MID and HIGH bands, so you can colour only the part you want.
What's the difference between TUBE and EXACT?
TUBE drives a warm, lopsided triode curve: it adds mostly the 2nd harmonic, more of the 3rd and above as you push it, and rounds peaks softly, reacting to how hard you play. EXACT adds exactly the 2nd, 3rd, 4th and 5th harmonics you set on the four faders, at the same ratio at any level, without rounding anything. You can switch between them while the music plays; the change crossfades over 30 ms.
Where should I start?
A fresh instance (Default ▸ Init) is TUBE at DRIVE 40 % with every band at 100 %, and AUTO GAIN on. For a specific job, load a preset for your instrument, the mix bus or the master, for example Vocals ▸ Vocal Warmth or Mix Bus ▸ Analog Summing; each preset's note says which control to move first. You don't need to gain-stage into the plugin, because the presets behave the same on a quiet track and a hot one.
Why are the 2ND, 3RD, 4TH and 5TH faders dimmed?
The faders only work in EXACT, so they're dimmed while TUBE is selected; you can still set them, ready for when you switch. In EXACT, each fader sets that harmonic's level in dB against the note, from OFF (−48 dB) to −6 dB, and DRIVE moves all four together: at 100 % they're as set, at 50 % 12 dB under, at 25 % 24 dB under.
What do the LOW, MID and HIGH knobs and the split handles do?
The three knobs choose how much of the colour is made from each band; at 0 % a band is left clean. The splits default to 200 Hz and 3 kHz, and you move them by dragging the round handles at the top of the SPECTRUM display (double-click to reset). The dry signal itself is never filtered: you hear your input untouched, plus the harmonics.
I turn DRIVE and hardly hear a difference. Why?
That's AUTO GAIN keeping the loudness where it was, so the change is in the colour rather than the level. Compare with bypass, listen on small speakers, or switch AUTO GAIN off for a moment to hear how much is being added. Also check that the band you want coloured isn't at 0 %, and if you're using EXACT on the HIGH band, keep the MID | HIGH split below about 6 kHz, since EXACT makes its harmonics from what is under about 6.4 kHz (at 48 kHz).
Why does TUBE on the HIGH band make the top duller, and why did my drums lose punch?
TUBE rounds peaks, and on cymbals and consonants that takes off more than its harmonics add, so for air use EXACT with LOW and MID at 0 %, as the air presets do. On drums the hits sit far above the band's usual level, so TUBE rounds them quickly: lower DRIVE, use MIX at 30 to 50 % for parallel saturation, or switch to EXACT, which rounds nothing.
Does it add latency? Can I sing or play through it while recording?
It has a constant latency of 1,216 samples at 44.1 and 48 kHz (about 25 ms), 2,368 at 88.2 and 96 kHz and 4,608 at 176.4 and 192 kHz, which your DAW compensates on playback. That's too much to play or sing through while recording, so insert it after recording or bypass it while tracking. It works on mono and stereo tracks.
The peaks went up on my master. What should I do?
TUBE's lopsided curve can raise an already limited master's peaks by up to 2 dB at high DRIVE. Keep TUBE at a low DRIVE (the Mastering presets use 12 to 14 %), use EXACT, or put your limiter after VEIRA Harmonic Saturator.