VEIRA Multiband Blue

What does VEIRA Multiband Blue do?

It is the console-bus one of the four VEIRA colour multiband compressors, painted 1970s steel blue. It splits your sound into four bands and gives each the classic British console’s bus compressor: a feed-forward VCA that reads the band’s RMS level and turns it down smoothly, with THRESHOLD, RATIO (1:1 to 20:1, a 6 dB soft knee), ATTACK, RELEASE and MAKEUP with AUTO, plus SOLO, BYPASS and M/S per band. Three crossovers are dragged on the BANDS display; it adds no latency by default, or 24 ms with LINEAR PHASE, and EXT KEY lets each band listen to the same band of a sidechain. MIX blends the result in phase and OUTPUT sets the level.

How do I set the crossovers?

Drag the numbered handles at the bottom of the BANDS display; double-click one for its default. Crossover 1 runs from 30 to 500 Hz (default 120 Hz), crossover 2 from 150 Hz to 5 kHz (1 kHz) and crossover 3 from 1.2 to 16 kHz (6 kHz); they stay in order and at least 1.25 times apart. Put each where one job ends and the next begins: 80 to 150 Hz between the kick and bass and the body of a mix, 500 Hz to 2 kHz between the body and the presence, 4 to 8 kHz below the air and the esses. SOLO a band (with MIX at 100 %) to hear exactly what falls in it. Moves glide, so you can make them while the music plays.

What does AUTO do?

AUTO is automatic makeup for each band. It keeps track of the energy the compressor took from the band over the last 3 seconds and gives it back, up to 18 dB, so the band’s peaks are held while its usual level stays, and it doesn’t pump back up after each hit. Notes 12 dB apart came out 8.7 dB closer while the band’s energy moved 0.11 dB. It is on by default and in most presets, so the balance of the mix doesn’t change while you compress. MAKEUP still adds on top of it, from −12 to +24 dB, when you want to push a band forward or pull it back.

When should I use LINEAR PHASE?

By default the crossovers add no latency: the four bands add back up flat in level, with an analog crossover’s phase turns around each crossover, which is right while recording, on single tracks and on most buses. LINEAR PHASE makes the bands add up to a pure delay, so every frequency comes out in time, as it went in; use it on a master or a mix bus. It costs 1152 samples of latency at 44.1 and 48 kHz (24 ms; 2304 at 96 kHz, 4608 at 192 kHz), reported to your DAW, whose bypass is delayed to match. Because it changes the latency it can’t be automated: when you switch it, the sound fades out over 20 ms and back in once the new filters are full. All the Mastering presets use it.

What does M/S do in a band?

With M/S off, a band works in stereo: both channels are measured together and turned down by the same amount, so the stereo image never moves. With M/S on, the band is split into its mid (L + R, the centre) and its side (L − R, the width), and each is detected and compressed on its own with the band’s settings. A wide, loud part in the highs can then be held without touching the vocal in the centre: a loud side-only tone was held 16.8 dB while a quiet centred tone in the same band changed 0.000 dB. Mix Bus ▸ Wide Side Control and Mastering ▸ Master M/S Width use it in the upper bands.

How do I use EXT KEY?

Route the key, a kick for example, to VEIRA Multiband Blue’s sidechain input in your DAW (it accepts a mono or stereo key), then switch EXT KEY on; the button is dimmed while no key reaches it. Every band’s detector then listens to the same band of the key: band 1 of your bass to band 1 of the kick, and so on. Set the bands that should duck and leave the others at 0 dBFS and 1:1, as the Sidechain presets do: Kick Ducks Bass ducks only band 1. In the test a kick on the key ducked a bass 22.5 dB. The Sidechain presets are quieter than bypass on purpose, so set OUTPUT by ear.

Why does my bounce sound different from playback?

SOLO is a listening aid and is left out of offline bounces on purpose, so a bounce with a band still soloed is the full mix. If a band was soloed while you listened, you heard that band alone. Note also that SOLO works on the compressed bands: with MIX below 100 % the unprocessed signal still plays under them. If the difference is in timing, LINEAR PHASE adds 24 ms of latency, which your DAW compensates on playback and in bounces.

What presets does it come with?

42 factory presets in 10 folders: Default, Drums, Bass, Guitar, Keyboards, Vocals, Mix Bus, Mastering, Sidechain and Creative FX, from Drum Bus Glue, Even Bass Line, Vocal Even and Gentle De-Ess to Console Bus Glue, Master Glue, Kick Ducks Bass and Upward Squash. Each band’s THRESHOLD was set so its folder’s material reaches the band’s designed reduction, so on a quieter or louder track set each band’s THRESHOLD first (watch its meter), then RATIO. Every preset outside Sidechain comes out within 0.05 LU of bypass, and the Mastering presets use LINEAR PHASE. You can save your own with SAVE.