VEIRA Comp White
What does VEIRA Comp White do?
It is a transparent, modern compressor, the clean one of the four VEIRA colour compressors, painted pearl white. THRESHOLD, RATIO from 1:1 to infinity with a soft KNEE, ATTACK and RELEASE with a programme-dependent AUTO, MAKEUP with AUTO, stereo LINK, parallel MIX, a sidechain high-pass, an external key with LISTEN and a 3 ms LOOKAHEAD. It adds no colour of its own: with nothing to compress, the output is the input, bit for bit.
Which of the four colour compressors should I choose?
All four have a parallel MIX and show the reduction over your music; what differs is the kind of compressor. White is clean: an exact curve, LOOKAHEAD and an external key, for control you shouldn’t hear and for ducking. Red is punchy: a fast FET compressor with a 20 to 800 µs attack and ALL, for drums, rock vocals and room mics. Gold is warm: a tube optical leveller with one PEAK REDUCTION knob, for vocals and bass that should sit still. Blue is vintage: a vari-mu tube compressor with six time constants and LAT/VERT, for mix-bus and master glue.
What does AUTO do on the release, and on the makeup?
AUTO release makes the release follow the music: a slow stage settles on the sustained reduction and lets go of it in 2.5 times RELEASE, while a transient’s excess comes back in 0.4 times RELEASE, so single hits recover quickly and dense passages don’t pump. AUTO makeup sets MAKEUP from the curve: it adds back what THRESHOLD, RATIO and KNEE take off a signal peaking at −15 dBFS, and the MAKEUP knob dims while it does. Check the meter bridge’s difference in LU before you judge.
What does LOOKAHEAD do, and does it change the latency?
With LOOKAHEAD on, the detector hears the music 3 ms before the audio arrives, so the gain is already coming down when a transient gets there: consonants and drum hits are caught cleanly. It doesn’t change the latency: VEIRA Comp White always delays the audio by 3 ms (144 samples at 48 kHz) and reports it to your DAW, so switching LOOKAHEAD never moves your track in time.
How do I use the external key (EXT KEY)?
Insert Comp White on the track to turn down, route the key track to its sidechain input in your DAW (in Logic, the Side Chain menu at the top of the plugin; in Cubase or Nuendo, enable the side-chain input and send the key track to it), then switch on EXT KEY. EXT KEY is dimmed while no sidechain is connected. LISTEN lets you hear the key; offline bounces always leave it out. The Creative preset Kick Ducking Key is a ready-made start for ducking a part under the kick.
Why does a bass stay clean when I compress it?
Because the detector holds each peak for a quarter of RELEASE (at most 25 ms) before it lets go, which spans a bass note’s half-cycle, so the gain stays still instead of riding the waveform. From RELEASE 100 ms up, even a 20 Hz note compressed 10.5 dB measured no distortion. With a very short RELEASE (10 ms), the gain follows low notes and adds distortion, as on any compressor.
Does it add latency?
Yes: 3 ms, 144 samples at 48 kHz (132 at 44.1 kHz, 288 at 96 kHz), always the same whatever the settings, LOOKAHEAD included. It is reported to your DAW, which compensates automatically, and the host’s bypass is delayed by the same amount, so bypassing keeps the track in time.
What presets does it come with?
37 factory presets in 9 folders: Default, Vocals, Drums, Bass, Guitars, Keys, Mix Bus, Mastering and Creative. Each was measured through the plugin on matching material for its job: tracks aim at 4 to 10 dB of reduction, the mix bus and mastering presets at 2 to 3 dB. All but three are level-matched to bypass within 0.43 dB. If your track is hotter or quieter than −8 dBFS peak, move THRESHOLD by the difference first. You can save your own with SAVE in the preset bar.