VEIRA Comp Blue

What does VEIRA Comp Blue do?

It is a vintage tube variable-mu compressor, the vintage one of the four VEIRA colour compressors, painted 1970s steel blue, in the tradition of the classic vari-mu tube compressors of the late 1950s. Its ratio rises gradually with level, so it holds a mix together without ever sounding grabbed. INPUT and THRESHOLD set how hard it works, six TIME CONSTANT settings give the classic attack and release pairs, LAT/VERT compresses the mid and the side separately, and COLOUR adds the tube-and-transformer sound.

Which of the four colour compressors should I choose?

All four have a parallel MIX and show the reduction over your music; what differs is the kind of compressor. White is clean: an exact curve, LOOKAHEAD and an external key. Red is punchy: a fast FET for drums and forward vocals. Gold is warm: a tube optical leveller for vocals and bass. Blue is vintage: a vari-mu for the mix bus, the master and drum buses, anything that should be held together gently and sound a little older.

Where is the ratio control?

There isn’t one, as on the original: the tubes set the ratio, and it rises with level. Measured at a −20 dBFS threshold, it is about 1.2:1 at the threshold, 2.5:1 at 8 dB over and 3.9:1 at 26 dB over. For a firmer hold, lower THRESHOLD or add INPUT; for a gentler one, raise THRESHOLD. The STATIC CURVE draws the knee for your settings.

Which TIME CONSTANT should I use?

1 (0.3 s release) for drums and anything that should recover between hits; 2 (0.8 s), the most used, for mix buses, vocals and bass; 3 and 4 (2 and 5 s) for a slow, steady hold. 5 and 6 are programme-dependent: after a single peak they let go in 2 s and 0.3 s, after several peaks in about 10 s, and 6 after sustained heavy compression in about 25 s, so dense passages are held steadily while isolated peaks recover quickly. On a master, 5 and 6 are especially natural.

What does LAT/VERT do?

It is the classic lateral / vertical mode: the mid (what both speakers share) and the side (the width) are compressed separately, each with its own side chain. Loud wide parts, doubled guitars, wide pads or reverbs, are held without pulling down the vocal, kick and bass in the centre. Measured: a quiet centred tone under a loud side-only tone changes 0.00 dB in LAT/VERT, where LEFT/RIGHT pulls it down 8.9 dB. On loud wide passages the image can narrow a little; that is the effect.

What does COLOUR add?

The sound of the push-pull tube line amplifier and its transformers: mostly odd, low-order harmonics with the 3rd leading, and a little more on the bass from the iron. It grows with level, so quiet passages stay nearly clean: at 30 % a −12 dBFS tone gets 0.024 % THD, at 100 % a loud bass note several per cent. It runs at eight times the sample rate, so nothing aliases, and at 0 % the plugin is clean.

Does it add latency?

Yes: 98 samples at every sample rate (2.0 ms at 48 kHz), from the colour stage’s oversampling filters. It is constant whatever the settings, reported to your DAW, which compensates automatically, and the host’s bypass is delayed by the same amount. With COLOUR at 0 % and no reduction the output is the input, delayed, bit for bit, in both stereo modes.

What presets does it come with?

37 factory presets in 9 folders: Default, Vocals, Drums, Bass, Guitars, Keys, Mix Bus, Mastering and Creative, from Vari-Mu Glue and Programme Glue TC5 to Mastering TC6, Wide Bus LatVert and Tube Drive. Each preset’s THRESHOLD was fitted for its designed reduction on its folder’s material, then OUTPUT so it comes out as loud as it went in, within 0.10 dB outside Default and Creative. On your music, set THRESHOLD by the meter first, then OUTPUT by ear.