VEIRA Limiter Gold

What does VEIRA Limiter Gold do?

It is a true-peak mastering limiter with warmth built in, the warm one of the four VEIRA colour limiters, painted brushed champagne gold. GAIN and WEIGHT drive the music into an 8x oversampled TAPE or TUBE stage that rounds the peaks and adds smooth, low-order harmonics, and a clean brickwall then holds the ceiling in true peak. WARMTH sets how much: at 0 % Gold is a transparent true-peak limiter.

Which of the four colour limiters should I choose?

All four hold a true-peak ceiling with no overs, share the same loudness panel, TARGET and MATCH, and are built to reach −6 LUFS on a dense mix. What differs is the stage in front of the ceiling. White is clean: it changes the least, so start there if you’re not sure. Red is punch: its clipper keeps the drums hitting, for EDM, hip-hop, rock and dance pop. Gold is warm: tape or tube harmonics for a mix that feels thin or hard. Blue is vintage: optical or FET levelling and transformer colour for a mix that should breathe and glue.

Will it reach −6 LUFS on my mix?

On typical dense material, yes: on an EDM premaster peaking at −3 dBFS, Gold at its defaults reached −5.98 LUFS at +10.2 dB of GAIN, with the true peak at −1.05 dBTP and no overs. At −6 LUFS any limiter shapes the peaks; Gold’s colour is gentle harmonics, by design. It needs some WARMTH to get there: at WARMTH 0 % it is a plain limiter, and a plain limiter stops near −7.1 LUFS on that mix. WARMTH between 40 and 75 % rounds the fastest peaks inside the waveform, which is what reaches −6 LUFS.

TAPE or TUBE: what is the difference?

Both round the peaks and add low-order harmonics; they differ in which. TAPE is symmetric and leads with the 3rd harmonic, with tape’s record EQ around it, so loud highs round a little sooner: it glues and smooths. TUBE is asymmetric and leads with the 2nd harmonic, for a fuller, rounder sound. At the default WARMTH of 50 %, a 100 Hz note 3 dB under the ceiling gets about 1.0 % of harmonics with TAPE and 1.4 % with TUBE. Switching crossfades over 20 ms, so compare them while the song plays, with MATCH on.

What does MATCH do, and should I bounce with it on?

MATCH plays the result at the input’s loudness (K-weighted, over 3 seconds), so you can switch the plugin in and out and hear what the limiting does to the sound, not just that it got louder. The meters and the loudness panel keep measuring the real output. An offline bounce always leaves MATCH out; for a real-time bounce, switch it off first.

Does it add latency?

Yes, a constant 271 samples at 48 kHz (5.6 ms; 259 at 44.1 kHz), the lookahead and the oversampling filters. It is the same at every setting and reported to your DAW, which plays the track that much earlier, and the host’s bypass is delayed by the same amount, so a bypassed track stays in time. Put it on the master bus, last.

My bounce reads over the ceiling. Why?

Something after the limiter is changing the level: another plugin, the master fader, a pan law, or dither or a format conversion in the bounce. Put the limiter last on the master bus and leave the master fader at 0 dB. On its own it aims a hair under the CEILING, so a −1.0 dBTP ceiling reads about −1.05 dBTP on a standard true-peak meter, with no overs. A meter that reads sample peak will read a little lower; one with a different true-peak filter may differ by a few hundredths of a dB.

What presets does it come with?

40 factory presets in 10 folders: Default, Mastering, Pop, EDM, Hip-Hop, Rock, Acoustic, Stems and Buses, Streaming and Creative. Each one names a loudness TARGET and was measured through the real plugin on matching material: no preset produces an over. Your music will differ in level, so set GAIN by the loudness panel until TO TARGET reads about 0 LU, as each preset’s note says. You can save your own with SAVE.

VEIRA Limiter Gold · Help · VEIRA