VEIRA Mastering Suite
What is VEIRA Mastering Suite for?
It puts a whole mastering chain in one plugin: nine modules (EQ, GLUE, MULTIBAND, IMAGER, DYNAMIC EQ, DE-ESSER, SATURATION, CLIPPER and MAXIMIZER) that you can put in any order, with the MAXIMIZER always last to hold the true-peak ceiling. You can also load a reference track, a finished master you want yours to sound like, and compare and match your master against it at the same loudness.
Which preset should I start from?
Default: Init is the default chain, all gentle, at 0 dB GAIN; Clean Slate has every module off, and Safety Limiter is only the MAXIMIZER at −1 dBTP. For a target, the folders are sorted by destination and genre: Streaming aims at about −14 LUFS, Loud at −7 to −9 LUFS and Dynamic at −16 to −24 LUFS. Each preset's note in the preset menu states the loudness it aims for and which control to move first.
I loaded a preset but my master isn't at the loudness it says. Why?
Each preset's GAIN was calibrated on a premaster of about −15 LUFS peaking around −3 dBFS, so your mix will land somewhere else. Set the MAXIMIZER's GAIN (or use LOUDNESS MATCH) for the loudness first, then shape the rest.
How do I match my master to a reference track?
Click LOAD in the REFERENCE window and choose a finished master (WAV, AIFF, FLAC, OGG or MP3, up to 20 minutes). Click LEARN, play the fullest part of your song for 20–30 seconds and click LEARN again, then click TONE to set an EQ MATCH curve and WIDTH to set the IMAGER's six widths. Play the song and click LOUDNESS, then play again and click LOUDNESS once more, because two passes land within 1 LU.
What does LEVEL MATCH do?
With LEVEL MATCH on (the default), ORIGINAL and REFERENCE in LISTEN are turned to your master's loudness, measured over about 10 s. A louder version always sounds better at first, so this makes the A/B comparison fair: you hear what the chain changed in tone and dynamics, not that it's louder.
Why can't I drag the MAXIMIZER, and why do GLUE, DE-ESSER and CLIPPER say OFF?
The MAXIMIZER sets the final level and the true-peak ceiling, so it always stays in slot 9 and nothing can be dropped after it. GLUE, DE-ESSER and CLIPPER are off by default, waiting where they belong; click the lamp on a card (or the ON button in its panel) to switch a module on.
What does PLR in the LOUDNESS window mean?
PLR is TRUE PEAK MAX minus INTEGRATED: the punch left in your master, and it gets smaller the more you push GAIN. Streaming masters usually keep a PLR of about 10–13 LU, loud club and pop masters go down to about 6–8.5, and below about 6 LU most music starts to sound flat.
Does it add latency, and which modules use the most CPU?
Yes, a constant 8,592 samples at 48 kHz (179 ms), 8,572 at 44.1 kHz and 16,896 at 96 kHz, which your DAW compensates for on playback; moving or switching modules never changes it. That's far too much to play or sing through, so use it on the master bus after tracking or bypass it while you record. The MAXIMIZER, the SATURATION and the CLIPPER cost the most processing, and switching off a module you don't need saves its processing.
TONE, WIDTH or LOUDNESS does nothing when I click it. What's wrong?
Read the status line under the buttons, which says what's missing. TONE and WIDTH need a reference loaded and something learnt (LEARN on while the master plays, for at least a few seconds). LOUDNESS needs the master to have played so its loudness is measured, and the MAXIMIZER must be on.
My bounce sounds different from what I heard. Why?
Check LISTEN: if ORIGINAL or REFERENCE was selected, that's what you were hearing, not the master. An offline bounce always renders the master whatever is selected, so in a real-time bounce select MASTER first.