VEIRA EQ White
What does VEIRA EQ White do?
It is a parametric equalizer, the clean one of the four VEIRA colour EQs, painted pearl white. Eight bands, each a bell, a low or high shelf, a low or high cut from 6 to 96 dB/oct or a notch, sit as numbered points on a large curve over the live spectrum of your music. Drag a point for frequency and gain, use the mouse wheel for Q, and read exact values under the mouse. SOLO lets you hear what a band works on, AUTO GAIN keeps the loudness where it was, and PHASE chooses minimum or linear phase.
Which of the four colour EQs should I choose?
All four draw their curve over the live spectrum, keep their curves’ analog shape up to 20 kHz and show the same meter bridge; what differs is the kind of EQ. White is clean and surgical: eight bands of any shape, SOLO and minimum or linear phase, for precise fixes and transparent mastering. Red is mid/side: every band on the stereo signal, the mid, the side or one channel, with BASS MONO, AIR and WIDTH. Gold is warm: a passive tube program EQ with the low boost-and-attenuate trick, a silky top and TUBE drive. Blue is vintage: a 1970s British inductor console EQ with stepped frequencies and COLOUR. Each manual has a page comparing them.
Should I use MINIMUM or LINEAR phase?
MINIMUM phase adds no latency and behaves like an analog EQ: use it for recording, mixing, drums and anything live, and for hum notches, which it makes infinitely deep. LINEAR phase leaves the phase of the music untouched, for mastering and for buses or stems that are summed again, at a constant 8704 samples (181 ms at 48 kHz), reported to your DAW. It pre-rings a little before sharp transients with steep, low cuts, so keep drums with such cuts in minimum phase. The factory Mastering presets use linear phase.
What does SOLO do?
SOLO plays only what the selected band works on: a band-pass at a bell’s or notch’s frequency and Q, what a cut takes away, or the side a shelf shelves. Set a narrow bell, switch SOLO on and sweep FREQUENCY until a ring or a harsh spot jumps out, then turn SOLO off and set the gain. It follows the band you select, it isn’t saved in presets or automatable, and offline bounces always leave it out; turn it off before a real-time bounce.
What does AUTO GAIN do?
A boost makes music louder, and louder always sounds better for a moment. AUTO GAIN works out from the curve itself how much louder or quieter it makes typical music, weighted like a loudness meter, and takes exactly that back off, so you compare tone, not level. It reads the curve, not the music, so it never pumps, and the status line above the graph shows what it applies. Every factory preset but Init has it on.
Does it add latency?
Not in MINIMUM phase: none at all. In LINEAR phase a constant 8704 samples at 44.1 and 48 kHz (181 ms at 48 kHz; 17408 at 88.2 and 96 kHz), whatever the bands do, reported to your DAW, which compensates automatically; the host’s bypass is delayed by the same amount. The LATENCY read-out under the PHASE buttons shows it. Don’t monitor a live input through linear phase.
My notch doesn’t remove the hum completely. Why?
In linear phase no finite filter can follow a notch all the way down: at 60 Hz with Q 10 it reaches about −12 dB. Switch PHASE to MINIMUM, where a notch removes its frequency completely. The Surgical Fixes presets Hum 50 Hz and Hum 60 Hz already do: notches on the hum and its first three harmonics, in minimum phase.
What presets does it come with?
40 factory presets in 9 folders: Default, Drums, Bass, Guitar, Keys, Vocals, Mix Bus, Mastering and Surgical Fixes. Every preset but Init has AUTO GAIN on and was measured on matching material: each keeps the loudness within 0.5 LU, so switching presets changes the tone, not the level. The Mastering presets run in linear phase; most notes say which band to tune to your material. You can save your own with SAVE in the preset bar.