VEIRA EQ Red
What does VEIRA EQ Red do?
It is a mid/side equalizer, painted deep lacquered red, for mixing and mastering. Each of its eight bands works on the STEREO signal, the MID (the centre: vocal, kick, bass, what a mono speaker plays), the SIDE (the width: room, reverbs, wide guitars, cymbals), or the LEFT or RIGHT channel alone. The graph draws the mid and side curves over a live spectrum of each. BASS MONO, AIR and WIDTH shape the stereo field, and LISTEN plays the mid or the side alone.
Which of the four colour EQs should I choose?
All four draw their curve over the live spectrum, keep their curves’ analog shape up to 20 kHz and show the same meter bridge; what differs is the kind of EQ. White is clean and surgical: eight bands of any shape, SOLO and minimum or linear phase, for precise fixes and transparent mastering. Red is mid/side: every band on the stereo signal, the mid, the side or one channel, with BASS MONO, AIR and WIDTH. Gold is warm: a passive tube program EQ with the low boost-and-attenuate trick, a silky top and TUBE drive. Blue is vintage: a 1970s British inductor console EQ with stepped frequencies and COLOUR. Each manual has a page comparing them.
What are mid and side?
Mid is what both channels share, (L + R) / 2: the centre of the stereo picture and what a mono speaker plays. Side is what differs, (L − R) / 2: the width. Red works them out exactly and decodes them back, so with the EQ flat nothing changes, bit for bit. An EQ on the mid changes the centre, one on the side the width, so you can lift a vocal’s presence without brightening the cymbals, or take mud out of wide guitars without thinning the bass.
Will it change my mix in mono?
Only what is meant to. SIDE bands, BASS MONO, AIR and WIDTH act on the side, which cancels out of the mono sum, so they never change what a mono speaker plays: measured on a full mix with all of them working, the mono sum changed by −152 dB, rounding only. MID and STEREO bands change mono as they change the centre, and a LEFT or RIGHT band changes it by about half its gain.
What do BASS MONO, AIR and WIDTH do?
BASS MONO removes the side below MONO BELOW (20 to 500 Hz, a 24 dB/oct high-pass on the side), so kick and bass sit in the centre on every system; 80 to 120 Hz suits most masters. AIR is a high shelf at 10 kHz on the side only, up to +8 dB. WIDTH sets the side’s level from 0 % (mono) to 200 %; 105 to 120 % opens a mix, and pairing it with BASS MONO keeps the low end solid.
I hear only the room, or the vocal has gone. Why?
LISTEN is on SIDE or MID. It plays the side or the mid alone on both speakers so you can hear what a band works on; set it back to STEREO. It isn’t saved in presets or automatable, the meters always read the real output, and offline bounces always leave it out; set it to STEREO before a real-time bounce.
Does it add latency?
Not in MINIMUM phase. In LINEAR phase a constant 8704 samples at 44.1 and 48 kHz (181 ms at 48 kHz), reported to your DAW, which compensates; the host’s bypass is delayed by the same amount. In linear phase Red applies the whole stereo response as one filter, so mid, side, left and right bands stay exactly in time. Use minimum phase while recording.
What presets does it come with?
34 factory presets in 8 folders: Default, Drums, Bass, Keys And Synths, Vocals, Mix Bus, Mastering and Surgical Fixes, from M/S Polish and Vocal Forward Master to Stereo Synth Bass Mono and One-Sided Boom Fix. Every one but Init has AUTO GAIN on and was measured on matching stereo material for loudness, mid and side, correlation and the mono sum; each keeps the loudness within 0.5 LU. Mid/side presets need a stereo source.