VEIRA Imager Lite
What is VEIRA Imager Lite for?
It sets the stereo width of a track, a bus or a whole mix with one big knob. WIDTH runs from 0 % (mono) through 100 % (as recorded) to 200 % (twice as wide) and keeps the loudness where it was. Under it, STEREOIZE makes a mono part stereo, BASS MONO keeps the low end in the centre, and OUTPUT sets the level. A VECTORSCOPE with CORRELATION and BALANCE shows the result, and the MONO key lets you check it in mono.
How is it different from VEIRA 6-Band Stereo Imager?
VEIRA 6-Band Stereo Imager splits the signal into six bands and gives each its own WIDTH, STEREOIZE, PAN and ROTATE, with a STEREO FIELD display. VEIRA Imager Lite sets one width for the whole signal, with one STEREOIZE and one BASS MONO, and its WIDTH keeps the loudness the same as you turn it. Choose the Lite when you want the right width quickly; choose the 6-Band when different frequency ranges need different widths.
Why doesn’t it get louder when I widen?
Because WIDTH keeps the loudness on purpose. It measures how much side and mid the music has, over about a second, and sets the level of both so the whole sound stays as loud as it was: on a mix, the range from 0 to 200 % moves the loudness by about 0.01 LU. The price is that the centre comes down a little as you widen, so on a typical mix at 200 % a mono listener hears it about 2 dB quieter. Check with MONO after widening.
WIDTH does nothing on my track. Why?
The track is mono, or nearly. WIDTH changes the balance between the side and the mid, and a mono source has no side, so it is left exactly alone. Turn STEREOIZE up first: it makes side for a mono part, and WIDTH then sets how wide the result is. On a mono track, check that the plugin is inserted as mono-to-stereo.
What does STEREOIZE do, and is it safe in mono?
It makes a mono or narrow part stereo by adding a copy of its mid to the side that is always a quarter turn (90 degrees) from it. The mono sum stays exactly the same, left and right stay equally loud at every frequency, nothing goes out of phase even at 100 %, and nothing under 150 Hz is touched. Because it adds side and keeps the mid, the stereo level rises a little (about 1.2 LU on a mono synth at 65 %); use OUTPUT to bring it back.
How do I keep the low end mono?
Switch BASS MONO on and set its frequency, from 20 to 500 Hz (120 Hz by default). Under it the stereo part is removed at 48 dB per octave with a linear-phase filter; the mid is never touched, so the bass keeps its level and tone. 100 to 150 Hz suits most mixes, and 150 to 200 Hz a wide synth bass. Under about 60 Hz the slope is gentler, so for a firmly mono low end set it to 80 Hz or higher.
What is the MONO key for, and why is my bounce still stereo?
MONO plays the output in mono, so you can hear how the image folds down on a phone or a small speaker. It is a listening aid: offline bounces leave it out, so you can’t bounce a mono file by mistake. To make a track mono for good, turn WIDTH to 0 %.
Does it add latency?
Yes, a constant 1152 samples at 44.1 and 48 kHz (about 24 ms; 2304 at 88.2 and 96 kHz), because STEREOIZE and BASS MONO are linear-phase filters. It is the same at every setting and reported to your DAW, which compensates for it, and the host’s bypass is delayed by the same amount, so a bypassed track stays in time. It is made for mixing and mastering, not for playing through while recording.
What presets does it come with?
28 factory presets in 7 folders, four each: Default, Drums, Bass, Vocals, Mix Bus, Mastering and Mono Fix, from Gentle Width, Wide Overheads and Centred Lead to Mono Low End, Master Tight Lows, Mono Synth To Stereo and Out-of-Phase Lows. A preset sets WIDTH, STEREOIZE and BASS MONO; it never changes OUTPUT or MONO. Every preset that widens keeps the lows mono, and the Mastering presets stay between 85 and 120 %.