VEIRA Saturator White

What does VEIRA Saturator White do?

It adds warmth, density, edge or crush with four exact curves: SOFT, SMOOTH, HARD and DIGITAL. DRIVE pushes the signal into the curve, TONE chooses whether the highs or the lows are driven harder, LOW CUT and HIGH CUT shape the saturated sound, AUTO GAIN keeps the level and MIX blends the dry signal back in time. Everything that distorts runs at four times your session’s rate through each curve’s antiderivative, so even hard clipping stays free of fold-back. It is the clean one of the VEIRA colour saturators, on a light face with dark screens.

Which MODE should I choose?

SOFT bends smoothly from the first dB: warm, rounded, odd harmonics only, the classic soft saturation (0.26 % THD on a sine at −18 dBFS RMS at DRIVE 0 dB, 3.7 % at +12 dB). SMOOTH is a straight line up to −6 dBFS, then a soft knee: quiet parts pass untouched and only the peaks are shaped, ideal on vocals, mix buses and masters. HARD is perfectly clean up to 0 dBFS and then a hard ceiling: precise clipping for peaks, leads and fuzz. DIGITAL rounds and holds the signal with BITS and RATE: lo-fi on purpose. Changing MODE crossfades over 20 ms, so you can switch while playing.

What do BITS and RATE do?

They act only in DIGITAL and are dimmed in the other modes. BITS rounds every sample to a fixed number of steps, from 16 bits (clean) down to 2: at 8 a gritty noise follows the music, at 2 to 4 the sound breaks up. RATE holds each sample for a while, like a sampler running at a lower rate, from 48 kHz down to 1 kHz: whatever lies above half of RATE folds back down as inharmonic, metallic tones. That fold-back is the effect, so DIGITAL aliases on purpose; the other modes don’t.

What does TONE do? Is it an EQ?

No. TONE tilts the signal around 1 kHz before the curve, up to 12 dB from end to end, and applies the exact inverse tilt after it. Where the curve is clean the two cancel (to −121 dB), so you hear no change in tone; where it saturates, the side that was tilted up is driven harder. Turn it up and the highs get the most distortion, for a brighter, edgier sound; turn it down and the lows do, for a thicker, rounder one. A 5 kHz tone at DRIVE +9 dB came out 3.3 dB more compressed at +100 % than at −100 %. For EQ on the saturated sound itself, use LOW CUT (before the curve) and HIGH CUT (after it).

Why doesn’t it get louder when I turn up DRIVE?

Because AUTO GAIN is on (the default): it keeps a sine at −18 dBFS RMS at its level, within 0.006 dB, at any DRIVE and MODE, so turning up DRIVE changes the colour, not the volume, and you can judge the sound fairly. On dense material it is close but not exact, since dense sound is compressed more than a sine (noise came out within 1.6 dB): check the meter bridge’s Δ and trim with OUTPUT. Switch AUTO GAIN off and DRIVE also raises the level, until the 0 dBFS ceiling stops it.

Does it alias, and does it add latency?

Everything that distorts runs at four times your session’s rate, and each curve is applied through its antiderivative, which keeps what it makes above the audio range from folding back. With DRIVE +18 dB and a tone at −6 dBFS, the loudest component that isn’t a harmonic was −144 to −170 dB in SOFT and −91 to −136 dB in HARD; the same hard clip without either reached −28.5 dB. (DIGITAL aliases on purpose: that is its sound.) The cost is a fixed latency of 96 samples (2 ms at 48 kHz) at every rate and setting, reported to your DAW, which delays its bypass by the same amount.

How do I saturate in parallel?

Lower MIX: it blends the saturated signal with the dry one, delayed by exactly the same 96 samples, so the blend is in time and never combs, and at MIX 0 % the output is the input, delayed, bit for bit. LOW CUT and HIGH CUT shape only the saturated path, so you can drive only the mids and keep the lows clean underneath: Bass Parallel Drive takes the lows out of the driven copy at 120 Hz and blends it at 40 %. The parallel presets (Room Smash, Parallel Vocal Grit, Parallel Mix Crush, Parallel Destroy) use MIX between 25 and 45 %.

What presets does it come with?

41 factory presets in 10 folders: Default, Drums, Bass, Guitar, Keyboards, Vocals, Mix Bus, Mastering, Lo-Fi and Creative FX, from Kick Weight, Snare Crack and Bass Growl to Master Soft Clip, Twelve Bit Sampler and Fuzz Wall. AUTO GAIN is on in every one, and each comes out within 0.15 dB of bypass loudness (K-weighted) on the material it was made for. They were made on tracks peaking at −8 dBFS (drums −6, the mix bus −4, masters −3); how much a preset saturates depends on how hot your track is, so on a quieter track raise DRIVE by the difference, and on a hotter one lower it.