VEIRA Saturator Blue

What does VEIRA Saturator Blue do?

It is the console and rack one of the four VEIRA colour saturators, painted 1970s steel blue: drive and saturation from the 1970s and 80s British console and rack. CHANNEL is a console channel pushed into overdrive, IRON its output transformer saturating on the lows, and RACK an early-1980s digital rack unit’s converter driven past full scale. DRIVE (0 to +36 dB) pushes the music into the curve, TONE moves the distortion between the lows and the highs, LOW CUT and HIGH CUT choose what is driven, AUTO GAIN keeps the level where it was, and MIX blends the dry signal back in time. TRANSFER and HARMONICS show what it does.

Which MODE should I use?

CHANNEL is the all-rounder and the default: round at first, firm when pushed, with a 2nd harmonic for warmth beside the odd ones (18 % THD on a 1 kHz sine at −12 dBFS with DRIVE at +18 dB); use it on drums, vocals, guitars and buses. IRON saturates everything under about 120 Hz through a much harder curve, mostly odd harmonics, thick and dense in the low end: a 60 Hz note distorts 3.4 times as much as a 1 kHz one; use it on bass, kick, organ and for weight on a bus. RACK is a hard clip followed by 12-bit grain whose step follows the signal in 6 dB steps, bright, hard and gritty (23 % THD at +18 dB); use it on drums and guitars that need edge, and for lo-fi effects.

What does TONE do?

TONE is a pre- and post-emphasis around 1 kHz. Before the curve it tilts the driven band, half of TONE up above 1 kHz and half down below it (or the other way); after the curve it applies exactly the opposite tilt. So the tonal balance of the clean sound never changes: only where the distortion is made moves. Towards + (up to +6 dB) the highs are driven harder, for edge, bite and presence; towards − (down to −6 dB) the lows are, for a thick, warm, round sound. +6 dB against −6 dB moved the highs’ 3rd harmonic up 21 dB. It glides over 20 ms, so you can move it while the music plays.

What do LOW CUT and HIGH CUT do?

They choose what is driven, not what you hear. Below LOW CUT (Off, or 20 Hz to 1 kHz) and above HIGH CUT (1 to 20 kHz, or Open), at 12 dB per octave, the music passes clean, only undriven; nothing is removed from your sound. Raise LOW CUT to keep the sub clean while the rest is driven: with LOW CUT at 400 Hz, a 60 Hz note through IRON at +24 dB stayed clean. Lower HIGH CUT to keep the top clean; it also trims the harmonics made, so there is less fizz. Set both close together for a narrow, distorted band, as Creative FX ▸ Telephone Drive does. At Open, HIGH CUT keeps a gentle low-pass at 0.45 times the sample rate in the driven band, so ultrasonic leftovers aren’t driven into the audible range.

Why doesn’t it get louder when I turn up DRIVE?

That is AUTO GAIN, on by default: it keeps the output as loud as the input, so you hear the colour, not louder. It works in two steps: DRIVE’s gain is taken off and the loudness the curve takes is put back at once, from a table measured for each MODE, so a knob move is matched immediately; then a slow correction matches the output’s loudness to the input’s over about the last 3 seconds (K-weighted, within ±12 dB). That slow step takes a few seconds to settle on new material. Switch AUTO GAIN off to hear the drive as a real channel would, louder as you push, and turn OUTPUT down first (as Creative FX ▸ Raw No Auto Gain does).

Does it add latency?

Yes: 98 samples at every sample rate (2.0 ms at 48 kHz), from the 8x oversampling of the curve. It is the same at every setting and MODE and is reported to your DAW, which compensates for it; your DAW’s bypass is delayed by the same amount, so switching it is seamless. MIX blends the dry signal delayed to match, so parallel saturation never combs, and at MIX 0 % the output is the input, delayed, bit for bit.

What do TRANSFER and HARMONICS show?

TRANSFER draws the output (up) for a slowly moving input (across), in full-scale units, from the engine’s own curve at your settings, with DRIVE, MODE, AUTO GAIN, MIX and OUTPUT in it; the dashed diagonal is no change. In IRON it draws two curves: the one for everything above 120 Hz and the lows’ harder one. A dot shows the music’s peak now, and it can sit off the curve, because a real peak mixes frequencies the curves treat differently. HARMONICS shows what the saturator makes of a 200 Hz sine at −12 dBFS, H1 to H10 in dBc, odd harmonics in blue and even ones in cream, with the THD; it is measured by running a copy of the engine whenever a setting changes.

What presets does it come with?

41 factory presets in 9 folders: Default, Drums, Bass, Guitar, Keyboards, Vocals, Mix Bus, Mastering and Creative FX, from Console Drum Push, Iron Kick Thump, Growl Above the Sub and Channel Crunch to Vocal Console Warmth, Console Bus Warmth, Mastering Iron and Telephone Drive. Each one’s OUTPUT was set so it comes out within 0.05 LU of bypass on the material it was made for, except Broken Rack, Iron Overload and Console Fuzz, which come out about 6 dB quieter so their peaks stay under −1 dBFS. On a much louder or quieter track set DRIVE first, then TONE, then LOW CUT and HIGH CUT. You can save your own with SAVE.