The Master Knob
What does The Master Knob do?
It masters a song with one giant knob. Turn MASTER up and the song gets louder in even steps, while a glue compressor, four density bands, a touch of air, mono lows under 120 Hz and the drive into a true-peak limiter work a little firmer behind it, automatically. Its own sound, a wide cut of −5.0 dB at 350 Hz, is always on. Besides MASTER there are INPUT TRIM with MATCH, OUTPUT CEILING, a level-matched BYPASS LISTEN and optional dither. Put it last on the master bus, or on a finished stereo mix.
How loud does it get?
On a typical dense, well-balanced mix premastered at −13 LUFS: about −13.7 LUFS at 0 %, −10.6 LUFS at 50 %, and about −6 to −7 LUFS at 100 %, kept clean. Each 10 % adds about 0.6 to 0.9 LU. A bass-heavy mix stops sooner, at about −8 LUFS, because the limiter never clips bass waves; it rises evenly to about 70 % and then holds at that clean limit. A sparse mix, a voice with a guitar or a piano, rises faster near the top.
What is the signature EQ, and can I turn it off?
It is The Master Knob’s own sound: a bell at 350 Hz, exactly −5.0 dB at its centre, with Q 1.2 (1.17 octaves between its half-gain points), plus a 20 Hz high-pass for rumble and DC. It is always on, at every position of the knob, and can’t be switched off: it takes the boxy part of the low mids out so the low end and the voice have room. If a mix already sounds thin around 300 to 400 Hz, give some back in the mix.
What does MATCH do, and when should I press it?
The knob’s curve was measured on premasters at about −13 LUFS integrated. Play the song for 10 seconds or more, ideally a chorus, and press MATCH: INPUT TRIM is set once, within −12 to +12 dB, so this mix comes in at −13 LUFS. The line under it shows the input’s loudness and how many seconds it has measured, and MATCH lights when it would change TRIM by 1 dB or more. It never moves on its own afterwards, and a preset never changes TRIM.
Which output ceiling should I use?
OUTPUT CEILING sets the master’s highest true peak, from −2.0 to −0.1 dBTP, and the limiter never goes over it. −1.0 dBTP, the default, suits every streaming service. −2.0 dBTP leaves room for lossy encoders (MP3, AAC, Opus) at low bit rates, as the Codec Safe preset does. −0.3 dBTP suits a CD or a file that won’t be encoded again, as CD Master 16-Bit does, with 16-bit TPDF dither.
How do I compare the master with my mix?
Use BYPASS LISTEN. MASTER plays the master turned down to the original’s loudness; ORIGINAL plays the original, as it came in and in time with the master. Switch between them to hear what the master does to the tone and the dynamics, not that it is louder. Nothing is ever turned up, so nothing can clip your converter. Set it back to OFF when you’re done; it never acts in an offline bounce.
What does CLEAN LIMIT mean?
It lights when MASTER asks for more than the music can take cleanly: when the limiter’s average reduction passes 5.5 dB, the drive backs off slowly and the light shows by how much. Usually it means the premaster is too hot, so play the song and press MATCH. At the top of the knob on a very dense mix it simply means you’ve reached as loud as that mix goes cleanly.
Does it add latency?
Yes, the limiter’s: 782 samples at 48 kHz (16.3 ms), the same at every setting and reported to your DAW, which compensates for it. Your DAW’s bypass stays in time too. The same input with the same settings gives the same output bit for bit, whatever the buffer size, whether you play it or bounce it.
What presets does it come with?
21 factory presets in 5 folders: Default, Streaming, Loud, Genres and Gentle, from Signature Only (0 %) and Jazz and Classical (10 %) to Quick Master (70 %), Codec Safe, CD Master 16-Bit and Maximum Clean (100 %). Each note gives the loudness it reaches on a typical dense premaster at −13 LUFS, so press MATCH first. A preset sets MASTER, the ceiling and dither, never INPUT TRIM or BYPASS LISTEN. You can save your own with SAVE.