VEIRA Saturator
What is VEIRA Saturator for?
It adds harmonics, the tones above each note that make a sound warmer, thicker, brighter, grittier or wilder, in eight STYLES: WARM, TAPE, TUBE, CRUNCH, CLIP, FOLD, RECTIFY and BIT. MORPH blends any two of them into a new curve, and up to three bands let the lows, the mids and the highs each take their own style and DRIVE. AUTO GAIN keeps the level, so turning DRIVE up changes the colour, not the loudness. Use it on drums, bass, guitars, keys, vocals, the mix bus and the master.
How is it different from VEIRA Saturator White, Red, Gold and Blue?
The four colour saturators are one colour each: three or four characters of one kind (clean curves, analog pedals, valve and tape, console and rack), with LOW CUT and HIGH CUT to shape what is driven. VEIRA Saturator is the modern all-rounder: eight styles of every kind on one panel, MORPH between any two, up to three bands with their own style and DRIVE, and DYNAMIC, which lets the drive follow the music. DRIVE, AUTO GAIN, MIX and the TRANSFER and HARMONICS displays work the same way. It is not part of a colour bundle.
Which STYLE should I choose?
WARM for thickness without edge (mostly the 2nd harmonic): bass, kick, vocals, a thin mix. TAPE to round the peaks and glue: drum and mix buses, pads, acoustic guitar. TUBE for warmth with presence (the 2nd and the 3rd): guitars, electric piano, snare, vocals. CRUNCH for firm grit: drums, rhythm guitar, organ. CLIP to shave peaks cleanly for loudness. FOLD for bright, metallic tones, RECTIFY for an octave-up fuzz on loud notes, and BIT for digital grain and a lower sample rate. Choose the style at a fairly high DRIVE, where it is easy to hear, then turn DRIVE down until it sits.
What does MORPH do?
Each band has a STYLE and a STYLE B. MORPH blends the two curves point by point: at 0 % only STYLE sounds, at 100 % only STYLE B, and in between a new curve with something of both, not two sounds mixed. Choose STYLE B with the STYLE B key, or Shift-click (or right-click) a style tile; the tile shows a small B while MORPH is above 0 %. MORPH moves smoothly while the music plays, so you can sweep or automate it with no zipper noise. Try Creative FX ▸ Morph Fold To Clip.
How do the bands work?
BANDS splits the sound into 1, 2 or 3 bands. In the strip, click a band to show and set it, drag the gap between two bands to move that crossover (40 Hz to 6 kHz and 200 Hz to 10 kHz, 24 dB per octave; double-click for 180 Hz or 2.5 kHz), press S to solo a band and B to bypass it. Each band has its own DRIVE, STYLE, STYLE B, MORPH and BAND MIX. Undriven, the bands add back to the input flat within 0.0001 dB, so only what you drive changes. Changing the number of bands while playing crossfades, with no gap, over a tenth to a third of a second.
Why doesn’t it get louder when I turn DRIVE up?
That is AUTO GAIN, on by default: it gives back what the curve takes at once, then matches the loudness to the input over the last three seconds, so you judge the colour, not the volume. On music at DRIVE 60 %, six of the styles came out within 0.12 dB of the input; FOLD and RECTIFY read about 1 dB lower on a plain level meter, because loudness counts their added highs. The correction may settle over a few seconds after a change. Switch AUTO GAIN off and DRIVE is also gain, up to +36 dB; CLIP then becomes a loudness clipper at 0 dBFS.
What do DYNAMIC and TONE do?
DYNAMIC lets each band’s drive follow its level, up to 18 dB either way around −24 dBFS: + drives the hits and attacks harder, − drives the quiet parts harder for a denser, more even body. At 0 % the drive is steady. TONE tilts around 800 Hz, 3 dB each way at the ends. At PRE it tilts what goes into the drive and takes the tilt back out afterwards, so the balance stays and only the harmonics get brighter (+) or darker (−); at POST it is an EQ on the saturated sound.
Does it add latency, and when should I use HIGH?
It delays the sound by 194 samples at every sample rate and setting (4.0 ms at 48 kHz) and reports it, so your DAW compensates; the dry signal for MIX and the host’s bypass are delayed to match. QUALITY ECO runs the curves at 8 times the sample rate, HIGH at 16 times, with the same latency. At DRIVE 50 % both keep aliasing under −100 dBc (every style but BIT, whose lower rate is meant to fold back). Use HIGH when you drive bright, loud material past about 75 %, where it is 30 to 50 dB cleaner, and on the master.
What presets does it come with?
50 factory presets in 10 folders: Default, Drums, Bass, Guitar, Keyboards, Vocals, Mix Bus, Mastering, Multiband and Creative FX, from Drum Crunch Bus, Bass Three Ways and Clean Guitar Glow to Vocal Tape Warmth, Mix Glue Tape, Master Tape Polish, Air Exciter, Three Colours and Wavefold Madness. Every style is used. AUTO GAIN is on in all of them, and each comes out as loud as it went in, within 0.05 dB, on the material it was made for. On hotter material the colour is stronger: adjust DRIVE first. You can save your own with SAVE.