VEIRA Limiter Red
What does VEIRA Limiter Red do?
It is a true-peak mastering limiter, the punchy one of the four VEIRA colour limiters, painted deep lacquered red. An 8x oversampled punch clipper rounds the first milliseconds of the hits that jump out of the music, and behind it the engine of VEIRA Limiter White holds the true-peak ceiling. Because the hits are clipped instead of the whole mix being turned down on each one, the groove doesn’t duck and the drums keep hitting at loudness. PUNCH sets how the work is shared.
Which of the four colour limiters should I choose?
All four hold a true-peak ceiling with no overs, share the same loudness panel, TARGET and MATCH, and are built to reach −6 LUFS on a dense mix. What differs is the stage in front of the ceiling. White is clean: it changes the least, so start there if you’re not sure. Red is punch: its clipper keeps the drums hitting, for EDM, hip-hop, rock and dance pop. Gold is warm: tape or tube harmonics for a mix that feels thin or hard. Blue is vintage: optical or FET levelling and transformer colour for a mix that should breathe and glue.
Will it reach −6 LUFS on my mix?
On typical dense material, yes: on a premaster peaking at −3 dBFS it reached −6.00 LUFS at +9.1 dB of GAIN, with the true peak at −1.07 dBTP and no overs, without distortion you can hear. At −6 LUFS any limiter shapes the peaks; Red shapes the hits rather than the groove. It never clips held bass, so on very sub-heavy mixes it can stop just short: a kick, bass and pads mix stopped at −6.5 LUFS. Try more PUNCH, which reaches the same loudness with less GAIN; if the loudness still stops moving, back off, or try Gold or Blue.
How should I set PUNCH?
PUNCH sets how much of the peak control the clipper does. At 0 % it is out and Red is all limiter; at the default 50 % the hits that jump out of a dense mix are clipped while the rest is limited; at 100 % the hits are clipped hard, reaching the same loudness with about 1 dB less GAIN. Held notes, chords and voices always ride under the clipper. Turn PUNCH up while the drums lose their hit and down when the cymbals or the snare start to sound edgy, and compare with MATCH on.
What does MATCH do, and should I bounce with it on?
MATCH plays the result at the input’s loudness (K-weighted, over 3 seconds), so you can switch the plugin in and out and hear what the limiting does to the sound, not just that it got louder. The meters and the loudness panel keep measuring the real output. An offline bounce always leaves MATCH out; for a real-time bounce, switch it off first.
Does it add latency?
Yes, a constant 448 samples at 48 kHz (9.3 ms; 436 at 44.1 kHz), the lookahead and the oversampling filters. It is the same at every setting and reported to your DAW, which plays the track that much earlier, and the host’s bypass is delayed by the same amount, so a bypassed track stays in time. Put it on the master bus, last.
My bounce reads over the ceiling. Why?
Something after the limiter is changing the level: another plugin, the master fader, a pan law, or dither or a format conversion in the bounce. Put the limiter last on the master bus and leave the master fader at 0 dB. On its own it aims a hair under the CEILING, so a −1.0 dBTP ceiling reads about −1.05 dBTP on a standard true-peak meter, with no overs. A meter that reads sample peak will read a little lower; one with a different true-peak filter may differ by a few hundredths of a dB.
What presets does it come with?
41 factory presets in 10 folders: Default, Mastering, Streaming, Pop, EDM, Hip-Hop, Rock, Acoustic, Mix Bus and Stems. Each one names a loudness TARGET and was measured through the real plugin on matching material: no preset produces an over. Your music will differ in level, so set GAIN by the loudness panel until TO TARGET reads about 0 LU, as each preset’s note says. You can save your own with SAVE.