VEIRA Limiter Blue
What does VEIRA Limiter Blue do?
It is a true-peak mastering limiter with a vintage front end, the vintage one of the four VEIRA colour limiters, painted 1970s steel blue. An OPTO or FET levelling stage gives the slower, programme-dependent limiting of 1970s hardware, COLOUR adds transformer iron to the lows and an output stage that rounds the fastest peaks, and a clean brickwall then holds the ceiling in true peak. The vintage stage gives back its own average reduction, so COMPRESS changes the density, not the loudness.
Which of the four colour limiters should I choose?
All four hold a true-peak ceiling with no overs, share the same loudness panel, TARGET and MATCH, and are built to reach −6 LUFS on a dense mix. What differs is the stage in front of the ceiling. White is clean: it changes the least, so start there if you’re not sure. Red is punch: its clipper keeps the drums hitting, for EDM, hip-hop, rock and dance pop. Gold is warm: tape or tube harmonics for a mix that feels thin or hard. Blue is vintage: optical or FET levelling and transformer colour for a mix that should breathe and glue.
Will it reach −6 LUFS on my mix?
Close to it, with no overs: at its defaults Blue reached −5.81 LUFS on a dense EDM premaster (+10.9 dB of GAIN) and −5.75 LUFS on a gentler pop mix, both with the true peak at −1.05 dBTP. So on such mixes it lands about −5.8 LUFS, a touch past −6; back GAIN off a little to sit right on your TARGET. At −6 LUFS any limiter shapes the peaks. It needs some COMPRESS or COLOUR to get there: with both at 0 % it is a plain limiter, which stops near −7.1 LUFS on that EDM mix.
OPTO or FET: what is the difference?
OPTO is an optical levelling amplifier: it reacts to an RMS-like level with a gentle 3:1 and a wide knee, and after a long, loud passage it holds up to half its reduction longer, the slow breathing of optical hardware. FET is a fast peak limiter: 4:1 with a firmer knee, a quick attack, and a recovery that is quick after short peaks and slower after sustained reduction. OPTO is happiest with ATTACK around 10 ms, FET from 0.2 to 2 ms. COMPRESS sets how much either one levels; at 0 % the stage is out.
What does MATCH do, and should I bounce with it on?
MATCH plays the result at the input’s loudness (K-weighted, over 3 seconds), so you can switch the plugin in and out and hear what the limiting does to the sound, not just that it got louder. The meters and the loudness panel keep measuring the real output. An offline bounce always leaves MATCH out; for a real-time bounce, switch it off first.
Does it add latency?
Yes, a constant 271 samples at 48 kHz (5.6 ms; 259 at 44.1 kHz), the lookahead and the oversampling filters. It is the same at every setting and reported to your DAW, which plays the track that much earlier, and the host’s bypass is delayed by the same amount, so a bypassed track stays in time. Put it on the master bus, last.
My bounce reads over the ceiling. Why?
Something after the limiter is changing the level: another plugin, the master fader, a pan law, or dither or a format conversion in the bounce. Put the limiter last on the master bus and leave the master fader at 0 dB. On its own it aims a hair under the CEILING, so a −1.0 dBTP ceiling reads about −1.05 dBTP on a standard true-peak meter, with no overs. A meter that reads sample peak will read a little lower; one with a different true-peak filter may differ by a few hundredths of a dB.
What presets does it come with?
40 factory presets in 10 folders: Default, Mastering, Pop, EDM, Hip-Hop, Rock, Acoustic, Stems and Buses, Streaming and Creative. Each one names a loudness TARGET and was measured through the real plugin on matching material: no preset produces an over. Your music will differ in level, so set GAIN by the loudness panel until TO TARGET reads about 0 LU, as each preset’s note says. You can save your own with SAVE.