VEIRA Multiband White
What does VEIRA Multiband White do?
It splits your sound into four bands with three crossovers you drag on the display, and gives each band its own exact, transparent compressor, so you can hold a boomy note, a harsh upper mid or a splashy cymbal without touching the rest. Each band has THRESHOLD, RATIO, ATTACK, RELEASE, MAKEUP or AUTO, SOLO, BYPASS and STEREO, MID or SIDE; MIX, OUTPUT, LINEAR PHASE and EXT KEY act on the whole. It is the clean one of the VEIRA colour multiband compressors, on a light face with dark screens.
Why do I only see one band’s knobs?
So that the window stays legible at 1280 × 800, the panel shows the controls of one band at a time, named above them (for example BAND 1 20 Hz - 120 Hz). Click a band’s tab at the left, or click the band on the BANDS display, to show its controls. Every tab shows its band’s range and gain reduction all the time, and your DAW saves which band was shown.
Zero latency or LINEAR PHASE: which should I use?
Zero latency (the default) uses Linkwitz-Riley crossovers that add up flat (within 0.0001 dB) and add no delay, so it is fine while tracking and on single tracks; where two bands meet, the phase turns gently. LINEAR PHASE uses 48 dB/oct linear-phase bands that add up to a pure delay, with no phase turns at all, which matters most on a mix bus or master with strong compression in neighbouring bands. It costs latency: 1152 samples at 44.1 and 48 kHz (24 ms at 48 kHz), 2304 at 88.2 and 96 kHz, 4608 at 176.4 and 192 kHz, reported to your DAW. Because it changes the latency, LINEAR PHASE can’t be automated: switch it while the transport is stopped.
What does AUTO makeup do?
With AUTO on (the default) each band gets back what the compression really took from its energy, so it keeps its usual level. It counts only moments within 10 dB of the band’s usual level, so a loud passage the band is there to hold doesn’t buy its makeup back: that passage stays held. Measured: a band swinging by 12 dB at −24 dBFS, 4:1, lost 9.6 dB without makeup and came back within 0.43 dB; a passage 18 dB over the band’s level was held 9.8 dB down and added only 0.07 dB of makeup. It needs a few seconds of music to settle. Switch AUTO off to set MAKEUP (−12 to +24 dB) yourself.
How do I use EXT KEY?
Route the key track to the plugin’s sidechain input with your DAW’s sidechain menu; while nothing is connected, EXT KEY is dimmed. With EXT KEY on, every band listens to the same band of the key instead of to itself: a kick on the key ducks only the low band of a bass, a voice only the mids of a music bed. A stereo key is summed to mono for detection, and STEREO, MID or SIDE still decides which part of your band is turned down. A keyed band gets no AUTO makeup, so it really ducks; set a band’s RATIO to 1:1 to leave it alone. The Sidechain presets start you off (Kick Ducks Bass, Voice Ducks Music).
What do STEREO, MID and SIDE do?
They choose what a band detects and compresses. STEREO compresses the band as a whole, both sides with one gain from the louder side, so the image doesn’t move. MID detects and compresses only the band’s middle, what both sides share, and SIDE only its sides, what differs between them; the other part passes untouched (measured to 0.0000 dB). Use MID to hold a centred bass or voice without touching the width, and SIDE to calm wide, splashy highs or a wandering low end. On a mono track, STEREO and MID do the same and SIDE has nothing to work on.
Why does a fast ATTACK still let the start of a hit through?
There is no lookahead, so even the fastest ATTACK (0.1 ms) acts only once the hit has started. That keeps transients alive and adds no latency, and it is how the bands even out level without squashing the punch. ATTACK and RELEASE are true time constants (the gain covers 63 % of a step in the time set), and after the level drops each band holds its reduction for a quarter of RELEASE (at most 25 ms), so a low band doesn’t ride the waveform. For tighter control of the peaks, put a limiter after it.
I soloed a band, but my bounce has every band. Why?
SOLO is a listening aid: use it to place the crossovers and hear what a band holds. Offline bounces always leave it out, so a bounce always has every band. BYPASS, on the other hand, is part of the sound: a bypassed band passes without compression or makeup, in playback and in bounces alike.
What presets does it come with?
41 factory presets in 10 folders: Default, Drums, Bass, Guitar, Keyboards, Vocals, Mix Bus, Mastering, Sidechain and Creative FX, from Drum Bus Punch, Vocal De-Harsh and Mix Bus Glue to Master Transparent, Kick Ducks Bass and Wide Side Pump. Every Mastering preset uses LINEAR PHASE and every Sidechain preset EXT KEY. Every preset but one comes out within 0.15 dB of bypass loudness (K-weighted) on the material it was made for; Over The Top is held 2.4 dB lower so its peaks stay under −0.7 dBFS. THRESHOLD works against each band’s own peak level, so on a quieter or louder track move every band’s THRESHOLD by the difference.