VEIRA Passive EQ
What does VEIRA Passive EQ do?
It is a tube program equalizer in the tradition of the passive program EQs of the 1950s, the unit on its own and laid out like a rack unit. Low shelves at 20, 30, 60 or 100 Hz that you can boost and attenuate at the same time, a resonant high boost from 3 to 16 kHz with its BANDWIDTH and a long, gentle high attenuation at 5, 10 or 20 kHz feed the make-up amplifier and its output transformer, which DRIVE pushes for warmth. Use it for broad, flattering moves on vocals, drums, bass, buses and masters.
Should I choose Passive EQ or EQ Gold?
Both have the same low and high curves, fitted to published measurements of the hardware. VEIRA EQ Gold adds a mid-range section below them (two broad peaks and a dip), a TUBE drive, a curve screen over the live spectrum and meters, in brushed champagne gold. VEIRA Passive EQ is the program EQ on its own: knobs and switches only, dials from 0 to 10 as on the hardware, and an amplifier with an output transformer that adds a little 3rd harmonic on heavy bass. Choose Gold if you want to see the curve and shape the mids; choose Passive EQ to work by ear on the classic unit.
How do I set the low-end trick?
Pick the low FREQ (60 Hz for a kick or a bass, 30 Hz for sub weight, 100 Hz for a voice), turn up BOOST for weight, then bring up ATTEN keeping it 2 to 3 steps under BOOST. The attenuation reaches much higher than the boost, so you get more weight below the frequency and a gentle dip above it that clears the mud. A step of ATTEN is worth more than a step of BOOST (1.75 dB against 1.35 dB), so equal dials nearly cancel at the bottom. Kick Weight (BOOST 6.5, ATTEN 3.5) gives +3.7 dB at 20 Hz and −1.7 dB at 450 Hz.
Why do the dials read 0 to 10 instead of dB?
As on the hardware. 10 is each section’s full range: +13.5 dB for the low BOOST, −17.5 dB for the low ATTEN, +18 dB for the high BOOST and −16 dB for HIGH ATTEN, and the dials are linear in dB, so 5 is half. The window under each knob shows what it does in dB, with a plus sign for a lift and a minus sign for a cut, so you never need to work it out. To type a value, right-click the knob: “6 dB” sets whatever dial gives 6 dB, “4.5” sets the dial to 4.5.
Why does ATTEN go up from 0 when it cuts?
Like every dial on the face, ATTEN reads 0 to 10, and turning it up cuts more. Its window shows the cut with a minus sign: ATTEN at 2.5 on the low section reads −4.4 dB, and at 10 −17.5 dB (−16 dB on HIGH ATTEN). BOOST windows show their lift with a plus sign. Used together on the same low frequency, keep ATTEN 2 to 3 steps under BOOST for the low-end trick.
Where are the curve screen and the meters?
There are none: the face is knobs and switches only, as on the classic units, an original 1950s rack design in green hammertone enamel. Work by ear, turn on AUTO GAIN so comparisons are about tone and not level, use EQ IN / OUT to hear the curve alone, and use your DAW’s meters for levels. If you want these curves with a curve screen and meters, VEIRA EQ Gold has them.
What does DRIVE do?
DRIVE pushes the make-up amplifier and its output transformer harder. The triode adds the 2nd harmonic, more on loud peaks than on quiet passages, which keep their level; the transformer adds a little 3rd on heavy bass. At 30 % the 2nd harmonic of a 1 kHz tone at −6 dBFS is at −35.4 dB; at 100 % it is at −22.7 dB. Everything runs at four times the sample rate, so nothing aliases above −85 dB. At 0 % the amplifier is clean, and with every dial at 0 the output is the input, bit for bit.
What do AUTO GAIN, EQ IN / OUT and the pilot lamp do?
AUTO GAIN takes off the loudness the curve adds or removes, worked out from the curve as music would hear it, so it never pumps; while it is on, a window under the switches shows the correction in dB. The EQ IN / OUT toggle switches the equalizer in or out over 20 ms, with the amplifier and OUTPUT left in place, so you hear only what the EQ does. The pilot lamp is lit while the EQ is in.
Does it add latency?
Yes: 64 samples at 44.1 to 96 kHz (1.3 ms at 48 kHz), from the oversampling filters, and none at 176.4 and 192 kHz. It is constant whatever the settings, reported to your DAW, which compensates automatically, and the host’s bypass is delayed by the same amount.
What presets does it come with?
63 factory presets in 12 folders: Default, Drums, Bass, Guitar, Keyboards, Strings, Brass, Woodwinds, Vocals, Mix Bus, Mastering and Creative FX, from Kick Weight and Bass Low-End Trick to Silky Vocal Top, Mud Cleanup, Master Low-End Trick and Old Radio. Each preset’s OUTPUT was fitted so its folder’s material comes out as loud as it went in, within 0.05 dB outside Creative FX. DRIVE was set for tracks peaking at −8 dBFS and buses at −4: on hotter tracks it colours more. You can save your own.