VEIRA Tape Saturator
What is VEIRA Tape Saturator for?
It records your track onto a model of a 2-inch, 24-track studio tape machine and plays it back, giving you the soft rounding of loud peaks, added harmonics, extra low-end weight and a gentler top. Use it for glue and warmth on a mix bus, drum bus or master, to fatten a bass or smooth a bright vocal, or, with WOW, FLUTTER and HISS, for cassette and lo-fi sounds.
What's a good first setting?
Choose CLASSIC as the TAPE TYPE and 15 for SPEED IPS, then play the loudest part of the track and turn up DRIVE until the VU needles reach about 0 VU for gentle colour, or +4 to +8 VU for an obvious tape sound. Leave AUTO GAIN on so you can compare fairly with bypass, and add the filters, transport noise and MIX only if you need them.
Which preset should I start from, and why does it sound different on my track?
Load a preset close to your job, for example Mix Bus ▸ Gentle Mix Glue, Drums ▸ Drum Bus Glue or Bass ▸ Bass DI Warmth. Tape reacts to level, and the presets assume tracks peaking around −8 dBFS (close drums −6, the mix bus −4 and a premaster −3 dBFS), so on hotter or quieter material set DRIVE by the VU meters first, then trim OUTPUT by ear.
I turned up DRIVE and nothing got louder. Is it working?
Yes: that's AUTO GAIN, which is on by default and takes the DRIVE back off after the tape, so you hear the tape working rather than the level going up. Listen for the rounding, the thickness and the softer top. Switch AUTO GAIN off if you want DRIVE to raise the level too, and use OUTPUT to bring it down.
How should I read the VU meters?
The RECORD LEVEL meters show the average level going onto the tape, after LOW CUT, HIGH CUT and DRIVE, with 0 VU equal to a sine at −18 dBFS RMS. As a guide on the loud parts: −6 to 0 VU is clean with a touch of glue, 0 to +4 VU is warm glue, +4 to +8 VU is obviously driven, and above +8 VU is crushed. Drums read lower than they sound, so judge them by ear and by the SAT lamp, which lights once the peaks are rounded off by about 1 dB or more.
What's the difference between the four tapes and three speeds?
MODERN is the cleanest with the most headroom, CLASSIC (the default) suits almost everything, WARM saturates earlier with more weight and thickness, and WORN adds grit, a duller top and more noise. At 7.5 ips the head bump sits at about 32 Hz with the softest top end, 15 ips (the default) puts it at about 55 Hz, and 30 ips at about 100 Hz with a flat top end for the cleanest, most open sound.
Why does the pitch wobble, or why is there noise?
Check WOW, FLUTTER and HISS: many Lo-Fi and Creative FX presets use them, while Init and most other presets keep them at 0 %. WOW and FLUTTER have a squared taper, so 50 % gives only a quarter of the full amount, and a good studio machine sits in the bottom 10–20 %. HISS at 50 % is the real noise floor of the chosen tape at its speed.
Does VEIRA Tape Saturator add latency?
Yes, a small, constant delay of 254 samples at 48 kHz (about 5 ms; 240 at 44.1 kHz, 437 at 96 kHz, 738 at 192 kHz), which your DAW compensates automatically. If you monitor a live input through it while recording you may notice it, so insert it after tracking or use your DAW's low-latency monitoring mode. It works on mono and stereo tracks.
I can't hear any difference. What should I check?
Look at the needles: if they sit well below 0 VU, the tape has little to do, so turn up DRIVE. A MODERN tape at 30 ips is also designed to be nearly transparent, so try CLASSIC or WARM at 15. And check that MIX isn't turned down, since at 0 % you hear only the dry signal.