VEIRA Mod Drive
What does VEIRA Mod Drive do?
It is a drive pedal into a modulation pedal, in one plugin, for electric guitars, keys and synths. DRIVE warms and breaks up the sound, from a touch of warmth to a fuzz, and TONE tilts it darker or brighter. Then the modulation sets it moving: CHORUS, FLANGER, PHASER, TREMOLO or VIBRATO, with RATE for how fast (in Hz, or with SYNC as a note value in time with your song) and DEPTH for how far. MIX blends the effect with the dry signal and OUTPUT sets the level. The 40 factory presets, in folders per mode plus Drive & Mod, Synced, Keys & Synths and Creative FX, are good starting points.
Does the drive make my track louder?
No. A real drive pedal gets louder as you turn it up; VEIRA Mod Drive takes that loudness back by itself, with a fixed makeup and AUTO GAIN, which measures the driven signal against the dry one while you play. Measured on strummed chords, the loudness stays within 0.5 dB from DRIVE 0 to 100 %, while the peaks come down (the drive rounds them). The drive is also set against your playing’s own level, so the same setting does the same on a quiet DI and a hot one, and there is no input gain to set. Give it a second or two when the playing starts: that’s how long it takes to learn your level.
What’s the difference between the five modes?
CHORUS adds two slightly delayed copies (around 12 ms) that drift against the dry sound: a wider, shimmering double. FLANGER sweeps a very short delay with feedback: the jet-plane whoosh, with more ring as DEPTH rises. PHASER sweeps six phase stages from 160 Hz upward: a smoother, swirling sound with a few wide notches. TREMOLO moves the level up and down, to silence at DEPTH 100 %. VIBRATO bends the pitch up to about a semitone either way, with no dry signal; at MIX 50 % it turns into a chorus. CHORUS, FLANGER and PHASER still move a little at DEPTH 0 %; for the drive alone, choose TREMOLO at DEPTH 0 % (the preset Warm Drive Only).
How does SYNC work?
With SYNC on, RATE is a note value from 2/1 to 1/32, with dotted (D) and triplet (T) values: one cycle of the modulation lasts that note at the song’s tempo, so 1/4 is one cycle per beat and 1/1 one per bar. The cycle is also locked to the song’s position: while the song plays, the plugin reads where it is and sets the movement there, so every bar moves the same way on every play and in a bounce, wherever you start playback. When the transport is stopped, the modulation keeps running at the tempo’s rate. The MOTION display shows the note value and what it comes to in Hz, for example 1/4 2.00 Hz at 120 BPM.
How do I get stereo from a mono guitar track?
Insert VEIRA Mod Drive as a mono-to-stereo plugin (in Logic Pro, choose Mono → Stereo; in most DAWs it’s what happens when you put a stereo effect on a mono track). The input is copied to both sides and processed as stereo: in CHORUS, FLANGER and PHASER the right side moves a quarter cycle behind the left, so a mono DI comes out wide and still sounds solid in mono. TREMOLO and VIBRATO move both sides together, so they stay centred. On a mono insert with a mono output, the plugin stays mono.
Will switching modes or turning DEPTH change my level?
No. Mixing a moving copy with the dry sound changes the loudness, by a different amount in each mode and at each depth, so the plugin trims every mode at every depth back to the loudness of the sound going in: measured on strummed chords, all of them stay within 0.7 dB. The tremolo raises its high points a little so its average holds. A MODE change crossfades over 60 ms, so switching never clicks, and every factory preset keeps the input’s loudness within 1 dB. If the level does change, check OUTPUT and the Δ readings on the meter bridge.
What is the latency?
64 samples at 44.1 to 96 kHz (1.3 ms at 48 kHz), and none at 176.4 and 192 kHz: the drive is computed at a higher internal sample rate so it stays clean, and that takes a few samples. The latency is constant and reported to your DAW, which compensates for it; the dry signal is delayed by the same amount, so MIX blends two paths lined up to the sample, and bypassed the plugin stays in time. You can play through it while recording: 1.3 ms is less than the time sound takes to reach you from an amp half a metre away.