VEIRA Bass Rig

What does VEIRA Bass Rig do?

It turns a bass recorded straight in (a DI track) into the sound of a recorded bass rig. It is laid out as a rig: a compressor made for bass, an overdrive that keeps the lows clean, an amp with three channels (VALVE, SOLID STATE and DRIVE), a cabinet with a microphone you can move, the DI blended in phase with it, and an EQ and a chorus after it. A gate, a tuner and meters sit around it.

How do I load it in my DAW?

It is an effect: insert it on the audio track with your bass, mono or stereo. On a mono track it plays in stereo; a stereo input is summed to mono for the amp, as one amp hears one bass. In Logic Pro it is under Audio Units ▸ VEIRA ▸ VEIRA Bass Rig, and in VST3 hosts under Fx ▸ Distortion.

How loud should my bass come in?

Aim for peaks of −12 to −6 dBFS on the IN meter, and set INPUT (±12 dB) to get there. Then set the GATE just above the noise between notes: it is slow enough for a bass, so a long note’s sustain rings out and a low note never makes it chatter.

How should I set the compressor?

Start from the default, SMOOTH at 4:1, and lower THRESHOLD until the meter shows 3 to 6 dB on the loud notes; give back the level with MAKEUP. Choose PUNCH and a higher ratio for slap, raise ATTACK to let the pluck through, and lower BLEND to mix the uncompressed bass back in. It never distorts the low notes and never pumps, so you can set it firmly.

Should the compressor go before or after the amp?

PRE, the default, evens out the bass as the amp hears it, and the clean DI with it: the amp responds more evenly. POST sits after the amp, the cabinet and the DI and holds the whole recorded sound together, for a level that never moves in the mix. Switching fades it out and back in.

What is the DI blend?

Engineers usually record a bass through a DI box and a miked amp at once. DI BLEND mixes in a CLEAN DI (the bass as a DI box records it) or an AMP DI (the amp without its cabinet). The DI is level-matched and phase-aligned with each cabinet, so blending it in adds weight and clarity instead of thinning the low end.

How do I move the microphone?

Drag it on the speaker, or in the side view, or turn POSITION and DISTANCE. POSITION goes from the centre of the speaker (brightest) to the edge of the cone (darker and rounder). DISTANCE goes from 1 cm, with the microphone’s proximity bass, to 60 cm, where you hear the other speakers, the floor and a little room. HORN sets the tweeter on the 4x10 and the 2x12 MODERN.

Can I use my own impulse response?

Yes. Click LOAD IR or drop the file on the speaker: WAV, AIFF or FLAC, up to 2 seconds. It is mixed to mono, its leading silence trimmed, matched to the session’s sample rate and levelled like the built-in cabinets, and the DI is aligned with it. The session keeps a copy; a user preset keeps only the file’s path and shows MISSING if the file is gone.

Does it add latency?

A little, and always the same: 58 samples at 44.1 and 48 kHz (1.2 ms at 48 kHz), 18 at 88.2 and 96 kHz, from the oversampling. It is shown on the panel and reported to your DAW, which compensates for it; the DI is delayed by the same amount, so it stays in phase. To play through it live, use a small buffer in your DAW.

How do I tune my bass?

Switch the TUNER on: it reads from 25 to 700 Hz, down to a five-string’s low B, shows the note and how many cents sharp or flat you are, and mutes the output while it is on, as a stage tuner does. Switch it off to play again.