VEIRA Bass Rig

A bass amp, its cabinet and a DI laid out as a rig: a studio bass compressor, an overdrive that keeps the lows clean, an amp with three channels, a miked cabinet blended with the DI in phase, and studio effects after it.

$129.99, a one-time purchase with free updates

VEIRA Bass Rig playing Vintage: Classic Stack: INPUT with the gate, a cream COMPRESSOR with its gain-reduction meter, a purple OVERDRIVE pedal and the TUNER on top; the amp on VALVE in the middle; the CABINET with its microphone and the DI, EQ, CHORUS and OUTPUT below.

VEIRA Bass Rig is a bass amp, its cabinet and a DI in one plugin, laid out as a rig: a studio bass compressor with its gain-reduction meter, an overdrive that keeps the lows clean, an amp head with three channels, a miked cabinet you can move the microphone on, blended with the DI, and studio effects after it. It is built to sound like a real recorded bass rig: a warm VALVE head, a punchy SOLID STATE and a gritty DRIVE that keeps the fundamental, each modelled stage by stage at eight times the sample rate, and a compressor that never distorts the low notes and never pumps.

Four bass cabinets designed in code take a dynamic, ribbon or condenser microphone that you drag across the speaker and away from it, or your own impulse response, kept inside the session, and the DI is blended in phase with the cabinet so the low end adds up. An EQ and a chorus that keeps the lows dry finish the sound, a gate, a tuner and meters sit around it, and the 31 factory presets in seven folders, from Studio Clean and Sixties Thump to Slap Snap and Doom Sludge, were levelled to play at the same loudness. Buy it once and VEIRA Manager installs it, like every plugin from VEIRA.

A tour of VEIRA Bass Rig

VEIRA Bass Rig playing Vintage: Classic Stack: INPUT with the gate, a cream COMPRESSOR with its gain-reduction meter, a purple OVERDRIVE pedal and the TUNER on top; the amp on VALVE in the middle; the CABINET with its microphone and the DI, EQ, CHORUS and OUTPUT below.
  1. The whole of VEIRA Bass Rig

    VEIRA Bass Rig is a bass amp, its cabinet and a DI in one plugin, built to sound like a real recorded bass rig. A compressor made for bass, with five ratios, parallel BLEND, SMOOTH or PUNCH and a gain-reduction meter, never distorts the low notes and never pumps. An overdrive drives only the mids and highs, and an amp with a warm VALVE, a punchy SOLID STATE and a gritty DRIVE channel is modelled stage by stage at eight times the sample rate. Four bass cabinets take a microphone you drag into place, or your own impulse response, and the DI is blended in phase with the cabinet, so the low end adds up instead of thinning out.

  2. The compressor

    Made for bass: no low-end distortion, no pumping.

  3. The amp

    Valve, solid state and drive, modelled stage by stage.

  4. Cabinet and DI

    Four cabinets, a microphone you drag, and the DI in phase.

  5. EQ, chorus and output

    An EQ and a chorus that keeps the lows dry.

What VEIRA Bass Rig does for you

The COMPRESSOR, on: its gain-reduction meter at −1.9 dB, THRESHOLD −22.0 dBFS, ATTACK 15 ms, RELEASE 200 ms, MAKEUP +4.0 dB, BLEND 100 %, RATIO 4:1, SMOOTH, and PRE chosen.

A compressor made for bass

THRESHOLD, RATIO from 2:1 to 20:1, ATTACK, RELEASE, MAKEUP and BLEND for parallel compression, with a gain-reduction meter. SMOOTH reads the level with a soft knee, like an optical compressor; PUNCH reads the peaks and grabs the pluck. It listens above 30 Hz and holds each reading for one period of a five-string’s low B, so it never distorts a low note, and its release follows your playing, so it never pumps. Put it before the amp or after the cabinet and the DI.

  • No low-end distortion
  • No pumping
  • Parallel BLEND
The purple OVERDRIVE pedal, off: DRIVE 45 %, TONE 50 %, BLEND 60 % and LEVEL 0.0 dB above its footswitch.

An overdrive that keeps the lows clean

A crossover at 160 Hz splits the bass: the lows always pass clean, and only the mids and highs go through the gain stage, with a middle push. BLEND sets how much of the drive replaces the clean mids and highs. At full DRIVE a 50 Hz note keeps 2 % distortion while a 500 Hz note has 34 %: grit and fuzz on top of a bottom that stays solid.

  • Lows under 160 Hz clean
  • BLEND
  • Grit or fuzz
The amp on VALVE: the CHANNEL buttons, DEEP, BRIGHT and CONTOUR, and GAIN 60 %, BASS 55 %, MIDDLE 60 %, MID FREQ 800 Hz, TREBLE 50 % and MASTER 66 %.

Three channels, modelled stage by stage

VALVE is a warm vintage all-valve head that stays clean on soft notes and blooms when you dig in. SOLID STATE is punchy, modern and hi-fi, with an active EQ. DRIVE is gritty and keeps the fundamental: its lows go through a gentle stage and only the middle and top through three high-gain stages. BASS, MIDDLE with five MID FREQ settings and TREBLE shape each one, with DEEP, BRIGHT and CONTOUR for a scooped modern tone, and every channel runs at eight times the sample rate.

  • Valve, solid state, drive
  • DEEP, BRIGHT, CONTOUR
  • 8x oversampling
The CABINET on 8x10: the 10-inch speaker with the microphone near the centre, the side view, DYNAMIC chosen, POSITION 25 %, DISTANCE 3.0 cm, HORN 40 %, CLEAN DI and DI BLEND 25 %.

Four bass cabinets and a microphone you can move

1x15 VINTAGE, 4x10, 8x10 and 2x12 MODERN, sealed or ported, with or without a tweeter, each designed from how bass speakers and boxes behave. Choose a DYNAMIC made for low instruments, a RIBBON or a CONDENSER and drag it on the speaker: POSITION from the bright centre to the darker edge, DISTANCE from 1 cm with its proximity bass to 60 cm with the room. HORN sets the tweeter for string noise, slap and pick.

  • 4 cabinets, 3 microphones
  • Drag the microphone
  • HORN level
The microphones, DYNAMIC chosen, with LOAD IR and CLEAR IR; CLEAN DI and AMP DI, CLEAN DI chosen; and POSITION, HORN, DISTANCE and DI BLEND at 25 %.

The DI, blended in phase

Engineers record a bass through a DI and a miked amp at once, and DI BLEND does the same: a CLEAN DI, as a DI box records the bass, or an AMP DI, the amp without its speaker. A cabinet turns the phase of the lows by more than a turn, so a DI mixed straight in cancels part of the low end. Here the DI is level-matched and turned with each cabinet’s phase: a 50 % blend stays within 1 dB of either alone, where it lost up to 5 dB without the alignment.

  • Clean DI or amp DI
  • Phase-aligned
  • No thin low end
The amp, the cabinet and the effects: VALVE with its tone knobs, the 8x10 with a dynamic microphone and the DI, EQ, CHORUS and OUTPUT.

Your own impulse response, steady loudness

LOAD IR takes your own impulse response, WAV, AIFF or FLAC up to 2 seconds, or drop it on the speaker; it is levelled like the built-in cabinets, the DI is aligned with it, and the session keeps a copy, so it plays the same anywhere. The three channels play at the same loudness, and GAIN and MASTER mostly add drive, not volume, so switching never jumps.

  • Your IR in the session
  • Channels at the same loudness
  • 1.2 ms latency
EQ, on, with LOW CUT 35.0 Hz, HIGH CUT 12.00 kHz, EQ FREQ 500 Hz and EQ GAIN 0.0 dB; CHORUS, off, with RATE, DEPTH and MIX; and OUTPUT at −2.1 dB with its peak meters and the latency, 1.21 ms.

EQ, chorus, a gate and a tuner

An EQ with a low cut for the rumble under the lowest notes, a high cut and a bell, and a CHORUS that keeps the lows under 180 Hz dry and centred, so it widens the top without blurring the bottom. The GATE is slow enough for a bass, so sustain rings out and a low note never makes it chatter, and the TUNER reads down to a five-string’s low B and mutes the output, as a stage tuner does.

  • Chorus with dry lows
  • A gate for bass
  • Tuner to low B
The preset browser showing Vintage: Classic Stack, with previous, next and SAVE.

31 presets in seven folders

Default, Clean, Vintage, Rock, Funk, Metal and Modern: from Studio Clean and Sixties Thump to Grit and Growl, Slap Snap, Doom Sludge and Five String Deep. Each preset was played with a bass part for its folder and levelled to −18 LUFS, so you can switch between them without reaching for the fader, and each note says what to try first.

  • 7 folders
  • Levelled to −18 LUFS
  • Save your own

Get VEIRA Bass Rig

Pay once and it’s yours, with every future update included.

VEIRA Bass Rig

A bass amp, its cabinet and a DI laid out as a rig: a studio bass compressor, an overdrive that keeps the lows clean, an amp with three channels, a miked cabinet blended with the DI in phase, and studio effects after it.

  • Yours to keep: pay once, no subscription
  • Every future update, free for life
  • VST3, AU, Standalone on up to 3 computers
  • Changed your mind? Cancel within 14 days (refunds)
USD

One-time payment, in your cart.

Welcome offer

Get 10% off your first order

Leave your email and we’ll send you a code for 10% off your first order, on any plugins. One code per person.

Specifications

Type
Bass amp, cabinet and DI simulator (effect): mono in to stereo out, or stereo to stereo, summed to mono for the amp
Compressor
THRESHOLD, RATIO (2:1, 3:1, 4:1, 8:1, 20:1), ATTACK 0.1 to 100 ms, RELEASE 20 ms to 1.5 s (program dependent), MAKEUP, BLEND (parallel); SMOOTH or PUNCH; before or after the amp; gain-reduction meter
Overdrive
DRIVE, TONE, BLEND, LEVEL; the lows under 160 Hz always pass clean
Amp
VALVE, SOLID STATE, DRIVE; GAIN, BASS, MIDDLE with MID FREQ (220 Hz to 3 kHz), TREBLE, MASTER; DEEP, BRIGHT, CONTOUR; valve stages, the passive tone stack, a power amp with feedback loop and sag; channels levelled
Oversampling
8x at 44.1 and 48 kHz (4x at 88.2 and 96 kHz, 2x above), anti-aliased curves; worst alias at full gain at least 92 dB below the note
Cabinet
1x15 VINTAGE, 4x10, 8x10, 2x12 MODERN; DYNAMIC, RIBBON or CONDENSER microphone; POSITION, DISTANCE 1 to 60 cm, drag the microphone; HORN; or your own IR (WAV, AIFF, FLAC, up to 2 s), embedded in the session
DI
DI BLEND 0 to 100 %, CLEAN DI or AMP DI, level-matched and phase-aligned with the cabinet
Effects
EQ (low cut 20 to 200 Hz, high cut, 12 dB/oct, a bell), CHORUS (rate, depth, mix; lows under 180 Hz dry and centred)
Utilities
Noise gate, tuner from 25 to 700 Hz (mutes the output), input and output peak meters
Latency
58 samples at 44.1 and 48 kHz (1.2 ms at 48 kHz), 18 at 88.2 and 96 kHz; constant and reported to your DAW
Parameters
46, all automatable; the user IR is saved with the session and in user presets
Presets
31 factory presets in 7 folders (Default, Clean, Vintage, Rock, Funk, Metal, Modern), levelled to −18 LUFS, plus your own
Window
1440 x 940 at 100 %, resizable from 50 to 150 %, opens at 75 %, saved with the session
CPU (measured)
About 6 % of one core for Init, about 9 % for the heaviest preset, cabinet included (48 kHz)
Formats
VST3, AU, Standalone
macOS
macOS 11 or later, Apple silicon or Intel (universal). VST3, AU and Standalone.
Windows
Windows 10 or later, 64-bit. VST3 and Standalone.
Pro Tools
Pro Tools (AAX) versions are built and tested, and arrive once they’re signed for Pro Tools.
Latest version
0.2.0, released November 17, 2026 · What’s new

Read more on the blog: Recording bass: the DI, the amp and the compressor

Questions? 10 answers about VEIRA Bass Rig

Works well with

VEIRA Amp Rig

A guitar amp and cabinet laid out as a rig: two pedals, an amp with three channels modelled stage by stage, a miked cabinet you can move the microphone on, and studio effects after it.

$129.99

VEIRA Bass DI Enhancer

A whole bass chain on one knob: an even low end, harmonics and a finished tone, at the same level.

$24.99

VEIRA Bass Rider

Rides a bass track’s fader for you, the way an engineer rides it through a song: set where the bass should sit, and one console fader evens out the sections and passages, within the limits you set.

$39.99