VEIRA Octaver
What does VEIRA Octaver do?
It sings along with a voice, an octave or two above it, below it, or both. OCTAVE UP and OCTAVE DOWN each have ON, a choice of +1 or +2 OCT (−1 or −2 OCT), LEVEL and PAN, DRY sets the singer’s own voice and OUTPUT the total. Only the pitch moves: the formants stay where they are, so the octaves sound like singers doubling the part an octave apart. The VOICES display draws the pitch sung over the last four seconds with the octaves around it, and the STEREO panel shows where each voice sits.
How is it different from an ordinary pitch shifter?
An ordinary pitch shifter, like a tape played faster or slower, moves the formants with the pitch: the resonances of the throat and mouth that make a voice sound like that person. Shifted up, a singer becomes a chipmunk; shifted down, a monster. VEIRA Octaver works on the voice’s own pulses, one period at a time, and changes only how often they come, so the formants stay where they were: measured on sung vowels, within 10 % of the singer’s own. The octave above sounds like a higher singer with the same mouth, the octave below like a lower one.
What can I use it on?
One note at a time: a singer, a rapper or a narrator, or a single-note guitar, bass or synth line. Consonants, breaths and noise have no pitch, so the octave voices pass them unshifted, about 12 dB down, and an octave never doubles an s. Chords get no octave: they pass through that same quiet copy instead of being garbled. Put it before reverb, delay, chorus and doubling effects, so it hears the dry voice; compression and EQ before it are fine.
Why do my bass’s low notes get no octave?
The pitch detector covers 72 Hz to 1000 Hz, which fits every singing voice from a bass to a soprano. Notes below about D2 (73 Hz), such as a bass guitar’s open E and A strings and the frets just above them, are under its range and pass quietly, unshifted. The Bass presets are for lines played from D2 up.
What does 0 dB LEVEL mean?
As loud as the singer. Each octave voice is level-matched to the dry voice, so at 0 dB it sits at the dry voice’s loudness on any vowel and any note, and −6 dB means 6 dB under it. −12 to −10 dB is weight or shine you feel more than hear, −8 to −6 dB a clear octave, 0 dB an equal second singer. On very high notes the octave above can come out up to about 3 dB quieter, and slightly breathier, than LEVEL says: raise LEVEL a little there, or use +1 OCT instead of +2 OCT.
How do PAN and the STEREO panel work?
PAN places each octave from L 100 to R 100. On a mono vocal track into stereo, the dry voice sits in the centre and the octaves spread around it; the pan law is constant power with 0 dB on each side in the centre, so a voice sounds equally loud wherever it is. On a stereo track the octaves are made from the sum of the channels and the dry signal keeps its stereo. If PAN does nothing, the output is mono: the STEREO panel reads MONO OUT. In Logic Pro, insert the plugin as Mono → Stereo.
Does it add latency?
Yes, a constant 29.1 ms (1398 samples at 48 kHz, 1290 at 44.1 kHz), reported to your DAW, which compensates for it on playback, so the track stays in time. The dry voice and the host’s bypass are delayed to match. With both octaves off, the output is the input, delayed, bit for bit. For a singer monitoring through it while recording, 29.1 ms is noticeable: record dry and add the octaves afterwards.
Why does the OUT loudness read 3 LU above IN?
On a mono track into stereo, IN measures the voice once, as one channel, while OUT measures it on two speakers, left and right, so the Δ reads about +3 LU even with both octaves off. Take 3 off to see what the octaves add. On a stereo track, or a mono track with a mono output, Δ reads directly.
Why does the octave come and go?
VEIRA Octaver needs one voice, dry. Reverb, delay or chorus before it, several voices on one track, a lot of noise or bleed, or notes below its range hide the pitch, and the octaves fall back to a quiet, unshifted copy. On the VOICES display those moments are gaps in the lines. Consonants and breaths leave gaps on purpose.
What presets does it come with?
37 factory presets in 8 folders: Default (Init: OCTAVE DOWN −1 OCT at −6 dB, OCTAVE UP off), Vocals, Backing Vocals, Rap & Spoken, Guitar, Bass, Synths & Keys and Creative FX. Every one makes at least one octave and was made for a mono source on a mono track into stereo. Each was run through the real plugin on its folder’s material: its loudness change stays within 1 dB of what its levels add up to, and its peaks at −3.2 dBFS or under. You can save your own with SAVE.