Blog

The low-end trick, done right: why BOOST sits above ATTEN

November 1, 2026 · 3 min read · VEIRA

The passive program EQs of the 1950s let you boost and cut the same low frequency at once. Here is why the two don’t cancel, why equal settings nearly do, and how to set the trick by ear.

VEIRA Passive EQ, a 1950s-style rack unit in green hammertone enamel with cream print, on a pop mix: LOW FREQUENCY at 60 Hz with BOOST +8.1 dB and ATTEN −4.4 dB, the high boost +4.5 dB at 10 kHz with BANDWIDTH Q 0.62, HIGH ATTEN −2.4 dB at 20 kHz, DRIVE 30 %, OUTPUT 0.0 dB, AUTO GAIN off, EQ in and the pilot lamp lit.

The passive program EQs of the 1950s have one move every engineer learns sooner or later: turn up the low boost and the low attenuation on the same frequency, at the same time. It sounds like it should do nothing. Instead it gives a kick, a bass or a whole mix more weight underneath and less mud just above. VEIRA Passive EQ is built in that tradition, with the same low shelves at 20, 30, 60 and 100 Hz, so it is a good place to learn how the trick really works.

Why the two shelves don’t cancel

Both low controls are gentle, first-order shelves made by the passive network, but they don’t reach equally high. At full boost the lift is still 3 dB at five to seven times the frequency on the switch (300 Hz for 60 Hz); at full attenuation the cut is still 3 dB at twelve to fifteen times it (800 Hz for 60 Hz). So below the frequency the boost wins and you get weight, and a little above it, where the boost has faded but the attenuation is still working, you get a gentle dip that clears the low mids.

The LOW FREQUENCY section on green hammertone enamel: FREQ at 60 Hz, BOOST at 6 reading +8.1 dB and ATTEN at 2.5 reading −4.4 dB, on bakelite knobs over printed 0 to 10 dials.
The LOW FREQUENCY section of VEIRA Passive EQ: FREQ at 60 Hz, BOOST at 6 and ATTEN at 2.5, the low-end trick on a pop mix.

The part almost everyone gets wrong

The dials read 0 to 10, as on the hardware, and a step of ATTEN is worth more than a step of BOOST: 1.75 dB against 1.35 dB. Set them to the same number and the attenuation, deeper and wider, eats the lift: equal dials nearly cancel at the bottom, and all you keep is the dip. VEIRA found this while building the factory presets, and the rule it gave is simple: the classic lift with a dip above it comes with BOOST 2 to 3 steps over ATTEN. The Kick Weight preset, BOOST 6.5 and ATTEN 3.5, gives +3.7 dB at 20 Hz and −1.7 dB at 450 Hz. With both at 10, the very bottom is only +0.9 dB and the dip deepens to −4.7 dB at 258 Hz.

Setting it by ear

  • Choose FREQ: 30 Hz for sub weight, 60 Hz for a kick or a bass, 100 Hz for a voice or warmth.
  • Turn up BOOST until the bottom has the weight you want, usually around 5 to 7.
  • Bring up ATTEN slowly, keeping it 2 to 3 steps under BOOST, and listen to the low mids clear.
  • Stop before the bass loses its body. If the lift disappears, ATTEN is too close to BOOST: lower it a step.

The dip sits higher than some descriptions of the trick suggest, around 450 to 550 Hz at 60 Hz with moderate settings, because the curves follow published measurements of the hardware’s network. Trust your ears more than a rule of thumb. On a master, keep it small: Master Low-End Trick uses 30 Hz with BOOST 3 and ATTEN 1.5.

The AMPLIFIER section: DRIVE at 30 % and OUTPUT at 0.0 dB.
The AMPLIFIER of VEIRA Passive EQ: DRIVE at 30 % and OUTPUT at 0.0 dB.

Judge it at equal loudness

A low boost adds level, and louder nearly always sounds better, so compare carefully. VEIRA Passive EQ has no curve screen and no meters, as the hardware had none, which keeps your attention on the sound. Turn on AUTO GAIN, which takes off exactly the loudness the curve adds, then flip the EQ IN / OUT toggle: the amplifier and OUTPUT stay in place, so you hear only the curve. DRIVE works on the EQ’s output, so a big low boost pushes it harder; listen again after you add a lot of BOOST.

The SWITCHES: the AUTO GAIN toggle down at OFF, the EQ toggle up at IN, and the jewel PILOT lamp lit.
The switches of VEIRA Passive EQ: AUTO GAIN, the EQ IN / OUT toggle and the jewel pilot lamp, lit while the EQ is in.

Read the VEIRA Passive EQ page for every measurement, or start from its presets: Kick Weight and Bass Low-End Trick for the low end of a mix, Broadcast Voice for a big radio voice, Mud Cleanup for a cloudy mix bus and Master Low-End Trick for a master.